Installation

INTERIOR PANELS / TRIM: ROOF HEADLINING: INSTALLATION

1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Install the 2 clips to the roof headlining assembly.

Text in Illustration

(b) Put the roof headlining assembly into the vehicle through the front door RH.

NOTICE:
Do not damage the roof headlining assembly or body interior.

(c) Engage the 2 clips.

Text in Illustration

(d) Install the roof headlining assembly with the 2 clips.

(e) Engage the 4 clamps to the front pillar LH.

(f) Engage the 3 clamps to the front pillar RH.

(g) Connect the bracket with the bolt to the front pillar RH.

Torque : 7.0 Nm (71 kgf-cm, 62 in-lbf)

(h) w/o Satellite Radio:

(1) Engage the 2 clamps and connect the connector to the rear pillar RH.

(i) w/ Satellite Radio:

(1) Engage the 2 clamps and connect the 2 connectors to the rear pillar RH.

(j) Connect the connector to the air conditioning thermistor assembly.

(k) w/ EC Mirror

(1) Connect the connector to the inner rear view mirror assembly.

2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Install the 2 clips to the roof headlining assembly.

Text in Illustration

(b) Put the roof headlining assembly into the vehicle through the front door RH.

NOTICE:
Do not damage the roof headlining assembly or body interior.

(c) Engage the 2 clips and 2 fasteners.

Text in Illustration

(d) Install the roof headlining assembly with the 2 clips.

(e) Engage the 4 clamps to the front pillar LH.

(f) Engage the 3 clamps to the front pillar RH.

(g) Connect the bracket with the bolt to the front pillar RH.

Torque : 7.0 Nm (71 kgf-cm, 62 in-lbf)

(h) w/o Satellite Radio:

(1) Engage the 2 clamps and connect the connector to the rear pillar RH.

(i) w/ Satellite Radio:

(1) Engage the 2 clamps and connect the 2 connectors to the rear pillar RH.

(j) Connect the connector to the sliding roof drive gear assembly.

(k) Connect the connector to the air conditioning thermistor assembly.

(l) w/ EC Mirror

(1) Connect the connector to the inner rear view mirror.

3. INSTALL VISOR HOLDER

(a) Engage the 2 claws.

(b) Push in the visor holder as shown in the illustration.

HINT
Use the same procedure for the other visor holder.

4. INSTALL VISOR ASSEMBLY LH

(a) Install the visor assembly LH with the 2 screws.

5. INSTALL VISOR BRACKET COVER (for LH Side)

(a) Engage the 4 claws to install the visor bracket cover.

6. INSTALL VISOR ASSEMBLY RH

HINT
Use the same procedure as for the LH side.

7. INSTALL VISOR BRACKET COVER (for RH Side)

HINT
Use the same procedure as for the LH side.

8. INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

(a) Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.

Text in Illustration

NOTICE:
After installation, check that the corners fit correctly.

9. INSTALL ASSIST GRIP SUB-ASSEMBLY

(a) Put a assist grip sub-assembly together as shown in the illustration.

(b) Engage the 2 clips to install the assist grip sub-assembly.

HINT
Use the same procedure for the RH side.

10. INSTALL REAR ASSIST GRIP ASSEMBLY LH

(a) Put a rear assist grip assembly LH together as shown in the illustration.

(b) Engage the 2 clips to install the rear assist grip assembly LH.

11. INSTALL REAR ASSIST GRIP ASSEMBLY RH

HINT
Use the same procedure as for the LH side.

12. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof) Installation

13. INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof) Installation

14. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof) Installation

15. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof) Installation

16. INSTALL PROTECTOR Installation

17. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) Installation

18. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Installation

19. INSTALL FRONT SEAT ASSEMBLY LH

for Manual Seat Installation

for Power Seat Installation

20. INSTALL FRONT SEAT ASSEMBLY RH

HINT
Use the same procedure as for the LH side.

21. INSTALL ROOF SIDE INNER GARNISH LH

(a) Engage the guide.

(b) Engage the 5 clips to install the roof side inner garnish LH.

22. INSTALL CENTER PILLAR UPPER GARNISH LH

(a) Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.

(b) Engage the clip.

(c) Install the center pillar upper garnish LH with the 2 screws.

23. INSTALL CENTER PILLAR LOWER GARNISH LH

(a) Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.

24. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH Installation

25. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side) Installation

26. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

Text in Illustration

NOTICE:
After installation, check that the corners fit correctly.

27. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the 6 claws to install the rear door scuff plate LH.

HINT
Engage the claws from the rear side of the scuff plate.

28. INSTALL ROOF SIDE INNER GARNISH RH

HINT
Use the same procedure as for the LH side.

29. INSTALL CENTER PILLAR UPPER GARNISH RH

HINT
Use the same procedure as for the LH side.

30. INSTALL CENTER PILLAR LOWER GARNISH RH

HINT
Use the same procedure as for the LH side.

31. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT
Use the same procedure as for the LH side.

32. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT
Use the same procedure as for the LH side.

33. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

Text in Illustration

NOTICE:
After installation, check that the corners fit correctly.

34. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure as for the LH side.

35. INSTALL REAR SIDE SEATBACK ASSEMBLY RH Installation

36. INSTALL REAR SIDE SEATBACK ASSEMBLY LH Installation

37. INSTALL REAR SEATBACK ASSEMBLY LH Installation

38. INSTALL NO. 2 ROOM PARTITION COVER Installation

39. INSTALL REAR SEATBACK ASSEMBLY RH Installation

40. INSTALL REAR SEAT CUSHION LOCK HOOK Installation

41. INSTALL REAR SEAT CUSHION ASSEMBLY Installation

42. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.

(b) Make sure that the front pillar garnish clip is not damaged.

NOTICE:
If there is any damage, replace the garnish clip with a new one.

(c) Install the front pillar garnish clip to front pillar garnish LH.

HINT
Install the front pillar garnish clip so that it faces as shown in the illustration.

(d) Engage the 2 guides as shown in the illustration.

(e) Engage the 2 clips to install the front pillar garnish LH.

43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

Text in Illustration

NOTICE:
After installation, check that the corners fit correctly.

44. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.

(b) Install the cowl side trim sub-assembly LH with the clip.

45. INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the 10 claws to install the front door scuff plate LH.

46. INSTALL FRONT PILLAR GARNISH RH

HINT
Use the same procedure as for the LH side.

47. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

Text in Illustration

NOTICE:
After installation, check that the corners fit correctly.

48. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT
Use the same procedure as for the LH side.

49. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure as for the LH side.

50. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

51. INSTALL LUGGAGE TRIM SERVICE HOLE COVER Installation

52. INSPECT SRS WARNING LIGHT

for Separate Type Yaw Rate Sensor: Separate Type Yaw Rate Sensor

for Built-in Type Yaw Rate Sensor: Built-in Type Yaw Rate Sensor