Operation CHARM: Car repair manuals for everyone.
Hosted by mcallihan.com
Home >> Toyota >> 2012 >> Camry L4-2.5L (2AR-FXE) Hybrid >> Repair and Diagnosis >> Instrument Panel, Gauges and Warning Indicators >> Dashboard / Instrument Panel >> Service and Repair >> Removal and Replacement >> Installation

Installation





INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: INSTALLATION

1. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

(a) Engage the 5 guides and temporarily install the instrument panel safety pad assembly as shown in the illustration.





NOTICE:
* Do not damage the instrument panel safety pad assembly.
* Do not allow the wire harnesses to interfere with the surrounding parts.

(b) Install the 2 clips.

(c) Install the 3 bolts and nut or .

(d) Install the 2 passenger airbag bolts or .

Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)

(e) Engage each clamp.

(f) Connect each connector.

2. CONNECT NO. 2 INSTRUMENT PANEL WIRE Installation

3. INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

(a) Engage the 10 clips to install the No. 1 instrument panel garnish sub-assembly.





4. INSTALL CONSOLE BOX INSERT

(a) Engage the clip and 3 guides.





(b) Install the console box insert with the 2 screws or .

5. INSTALL FRONT NO. 2 CONSOLE BOX INSERT

(a) Engage the 2 claws to connect the room temperature sensor.

(b) Engage the clip and 3 guides.





(c) Install the front No. 2 console box insert with the 2 screws or .

6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

(a) Connect the connector.

(b) Engage the 4 clips and guide to install the lower instrument panel finish panel assembly.

7. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) Installation

8. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

(a) Engage the 2 guides.





(b) Engage the 3 claws and 2 clips to install the No. 1 instrument panel speaker panel sub-assembly.

9. INSTALL FRONT PILLAR GARNISH LH Installation

10. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT
Use the same procedure as for the LH side Installation.

11. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

(a) Engage the 2 guides.





(b) Engage the 3 claws and 2 clips to install the No. 2 instrument panel speaker panel sub-assembly.

12. INSTALL FRONT PILLAR GARNISH RH

HINT
Use the same procedure as for the LH side Installation.

13. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

(a) Engage the 4 clips to install the No. 3 instrument panel register assembly.





14. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

(a) Engage the 5 clips to install the No. 2 instrument cluster finish panel garnish.





15. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

(a) Connect each connector.

(b) Engage the glove compartment light as shown in the illustration.





(c) Engage the 3 guides and 2 clips.





(d) Install the lower instrument panel sub-assembly with the 5 screws or .

16. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY Installation

17. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

(a) Connect the connector.

(b) Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.

18. INSTALL INSTRUMENT SIDE PANEL RH

(a) Engage the 3 guides.

(b) Engage the 4 claws to install the instrument side panel RH as shown in the illustration.





19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH Installation

20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT
Use the same procedure as for the LH side Installation.

21. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure as for the LH side Installation.

22. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers) Installation

23. INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY

(a) Connect the connector.

(b) Engage the 8 clips to install the No. 1 speaker opening cover assembly.





24. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio Receiver Type) Installation

25. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type) Installation

26. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Navigation Receiver Type) Installation

27. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

(a) Connect each connector.

(b) Engage the 4 clips and guide.

(c) Install the upper console panel sub-assembly with the 2 screws or .

28. INSTALL BOX BOTTOM MAT

(a) Install the box bottom mat.

29. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

(a) Engage the 6 clips to install the No. 2 instrument panel register assembly.





NOTICE:
When installing the No. 2 instrument panel register assembly, check that the wire harness is not caught between the No. 2 instrument panel register assembly and duct.

30. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

(a) Connect the connector.

(b) Engage the clamp.

(c) Engage the 6 clips and 7 claws to install the center instrument cluster finish panel assembly.





31. INSTALL REAR CONSOLE BOX ASSEMBLY Installation

32. INSTALL CONSOLE BOX CARPET Installation

33. INSTALL NO. 4 CONSOLE BOX DUCT Installation

34. INSTALL UPPER CONSOLE BOX SUB-ASSEMBLY Installation

35. INSTALL REAR CONSOLE UPPER PANEL SUB-ASSEMBLY

(a) Connect each connector.

(b) Engage the 4 clips and install the rear console upper panel sub-assembly.

(c) Move the shift lever to P.

36. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

(a) Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.





37. INSTALL FRONT PANEL GARNISH RH

(a) Engage the 3 claws, 2 clips and 8 guides to install the front panel garnish RH.

38. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY

(a) Engage the 4 claws, 9 clips and 3 guides.

(b) Install the lower No. 1 instrument panel finish panel assembly with the bolt and screw or .

39. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

(a) Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

40. INSTALL FRONT PANEL GARNISH LH

(a) Engage the 3 claws, 2 clips and 8 guides to install the front panel garnish LH.

41. INSTALL COMBINATION METER ASSEMBLY Installation

42. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

(a) Temporarily install the instrument cluster finish panel assembly as shown in the illustration.





(b) Connect each connector.

(c) Engage the 5 claws, 5 clips and 2 guides, and install the instrument cluster finish panel assembly.

(d) Engage the 2 claws, 4 clips and 2 guides.





43. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

(a) Engage the 4 clips to install the No. 1 instrument panel register assembly.





44. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

(a) Engage the 3 clips to install the No. 1 instrument cluster finish panel garnish.





45. INSTALL INSTRUMENT SIDE PANEL LH

(a) Engage the 3 guides.

(b) Engage the 4 claws to install the instrument side panel LH as shown in the illustration.





46. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH Installation

47. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH Installation

48. INSTALL FRONT DOOR SCUFF PLATE LH Installation

49. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

50. INSTALL LUGGAGE TRIM SERVICE HOLE COVER Installation

51. INSPECT SRS WARNING LIGHT

for Separate Type Yaw Rate Sensor: Separate Type Yaw Rate Sensor

for Built-in Type Yaw Rate Sensor: Built-in Type Yaw Rate Sensor
pro multis · About Operation CHARM