Installation
INTERIOR PANELS / TRIM: LOWER INSTRUMENT PANEL: INSTALLATION
1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(a) When using a new lower instrument panel sub-assembly:
(1) Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portions shown in the illustration.
(b) Install the lower instrument panel sub-assembly with the 4 bolts , 11 bolts
Text in Illustration
(c) Engage each clamp.
2. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/o Satellite Radio) Installation
3. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/ Satellite Radio) Installation
4. INSTALL GLOVE BOX LIGHT ASSEMBLY Installation
5. INSTALL GLOVE COMPARTMENT DOOR LOCK ASSEMBLY
(a) Engage the guide and claw.
(b) Install the glove compartment door lock assembly with the screw
6. INSTALL INSTRUMENT PANEL SAFETY PAD PLATE SUB-ASSEMBLY
(a) Install the instrument panel safety pad plate sub-assembly with the 2 bolts .
7. INSTALL POWER STEERING ECU ASSEMBLY (for Brush Type Motor) Installation
8. INSTALL POWER STEERING ECU ASSEMBLY (for Brushless Type Motor) Installation
9. INSTALL COMBINATION METER ASSEMBLY Installation
10. INSTALL NO. 1 HEATER TO REGISTER DUCT
(a) Install the No. 1 heater to register duct with the 3 clips.
11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT
Use the same procedure for the RH side and LH side Installation.
12. INSTALL FRONT DOOR SCUFF PLATE RH
HINT
Use the same procedure for the RH side and LH side Installation.
13. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
(a) Engage the claw to install the glove compartment door stopper sub-assembly.
14. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
(a) With the glove compartment door assembly opened approximately 55° from its closed position, engage the 2 hinges horizontally.
Text in Illustration
NOTICE:
Engaging the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.
(b) Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.
Text in Illustration
(c) Engage the claw and connect the glove compartment door stopper sub-assembly.
15. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
(a) Connect each connector.
(b) Engage the guide and 3 claws to install the No. 2 instrument panel under cover sub-assembly.
16. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation
17. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
(a) Connect each connector.
(b) Engage the guide and claw.
(c) Install the No. 1 instrument panel under cover sub-assembly with the 2 screws
18. INSTALL UPPER STEERING COLUMN COVER Installation
19. INSTALL LOWER STEERING COLUMN COVER Installation
20. INSTALL NO. 1 SWITCH HOLE BASE
(a) Connect the connector.
(b) Engage the 5 claws to install the No. 1 switch hole base.
21. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
(a) Temporarily install the console box assembly.
(b) Engage the 9 claws as shown in the illustration.
(c) Install the upper instrument panel finish panel assembly with the 2 bolts .
(d) Engage the clamp.
22. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY Installation
23. INSTALL AIR CONDITIONING CONTROL ASSEMBLY Installation
24. INSTALL CONSOLE BOX ASSEMBLY
(a) Connect the connector.
(b) Engage the 4 guides and 2 claws as shown in the illustration.
(c) Install the console box assembly with the bolt and 2 clips.
25. INSTALL BOX BOTTOM MAT
(a) Install the box bottom mat.
26. INSTALL FRONT NO. 2 CONSOLE BOX INSERT
(a) Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.
27. INSTALL FRONT NO. 1 CONSOLE BOX INSERT
(a) Engage the guide and 4 claws to install the front No. 1 console box insert as shown in the illustration.
28. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET
(a) Install the No. 2 console box mounting bracket with the 6 bolts .
29. INSTALL ELECTRICAL KEY OSCILLATOR Installation
30. INSTALL REAR CONSOLE BOX ASSEMBLY Installation
31. INSTALL CONSOLE BOX CARPET Installation
32. INSTALL REAR CONSOLE BOX CUP HOLDER Installation
33. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY
Installation
34. INSPECT SHIFT LEVER Installation