Operation CHARM: Car repair manuals for everyone.
Hosted by mcallihan.com
Home >> Toyota >> 2012 >> Prius L4-1.8L (2ZR-FXE) Hybrid >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Headliner >> Service and Repair >> Removal and Replacement >> Installation

Installation





INTERIOR PANELS / TRIM: ROOF HEADLINING: INSTALLATION

1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Put the roof headlining assembly into the vehicle through the back door.





NOTICE:
Do not damage the roof headlining assembly or body interior.

(b) Install the 5 clips.

(c) Connect the 2 connectors to the connector holder.

(d) Engage the 4 clamps to the front pillar LH.

(e) w/o Manual (SOS) Switch:

(1) Engage the 3 clamps and connect the connector to the front pillar RH.

(2) Disengage the clamp and disconnect the connector to the rear pillar RH.

(f) w/ Manual (SOS) Switch:

(1) Engage the 3 clamps and connect the 2 connectors to the front pillar RH.

(2) Engage the clamp and connect the 2 connectors to the rear pillar RH.

(g) w/ EC Mirror:

(1) Connect the inner rear view mirror connector and engage the 2 clamps.

(h) w/ Lane Keeping Assist System:

(1) Connect the inner rear view mirror connector and engage the clamp.





Text in Illustration





2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Put the roof headlining assembly into the vehicle through the back door.





NOTICE:
Do not damage the roof headlining assembly or body interior.

(b) Engage the 6 fasteners.





(c) Install the 3 clips.

(d) Connect the 2 connectors to the connector holder.

(e) Engage the 4 clamps to the front pillar LH.

(f) w/o Manual (SOS) Switch:

(1) Engage the 3 clamps and connect the connector to the front pillar RH.

(2) Disengage the clamp and disconnect the connector to the rear pillar RH.

(g) w/ Manual (SOS) Switch:

(1) Engage the 3 clamps and connect the 2 connectors to the front pillar RH.

(2) Engage the clamp and connect the 2 connectors to the rear pillar RH.

(h) w/ EC Mirror:

(1) Connect the inner rear view mirror connector and engage the 2 clamps.





Text in Illustration





3. INSTALL VISOR HOLDER

(a) Engage the 2 claws.





(b) Push in the visor holder as shown in the illustration.

HINT
Use the same procedure for the other visor holder.

4. INSTALL VISOR ASSEMBLY LH

(a) Engage the 2 clips to install the visor assembly LH.





5. INSTALL VISOR BRACKET COVER LH

(a) Engage the 3 claws to install the visor bracket cover LH.





6. INSTALL VISOR ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

7. INSTALL VISOR BRACKET COVER RH

HINT
Use the same procedure described for the LH side.

8. INSTALL FRONT ASSIST GRIP ASSEMBLY

(a) Assemble the front assist grip assembly as shown in the illustration.





(b) Install the front assist grip assembly.





HINT
Use the same procedure for the other front assist grip.

9. INSTALL REAR ASSIST GRIP ASSEMBLY

(a) Assemble the rear assist grip assembly as shown in the illustration.





(b) Install the rear assist grip assembly.





HINT
Use the same procedure for the other rear assist grip.

10. INSTALL NO. 1 ROOM LIGHT ASSEMBLY Installation

11. INSTALL MAP LIGHT ASSEMBLY (w/o Sliding Roof) Installation

12. INSTALL MAP LIGHT ASSEMBLY (w/ Sliding Roof) Installation

13. INSTALL LANE RECOGNITION CAMERA SENSOR ASSEMBLY (w/ Lane Keeping Assist System) Installation

14. INSTALL ROOF TOP MOULDING (w/o Lane Keeping Assist System)

(a) Engage the 3 claws and 2 clips to install the roof top moulding.





15. INSTALL ROOF TOP MOULDING (w/ Lane Keeping Assist System)

(a) Engage the 6 claws to install the roof top moulding.





16. INSTALL INNER REAR VIEW MIRROR COVER (w/ EC Mirror) Installation

17. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH

(a) Engage the 9 clips to install the roof side inner garnish assembly LH.





18. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

(a) Connect the connector.

(b) Engage the 7 claws and 2 clips.

(c) Install the deck trim side panel assembly LH with the screw.





19. INSTALL TONNEAU COVER HOLDER CAP (for LH Side)

(a) Engage the claw to install the tonneau cover holder cap.





20. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)

(a) Engage the 2 guides.





(b) Install the 2 luggage hold belt striker assemblies with the 2 bolts.

21. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

22. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

(a) Engage the 7 claws and 2 clips.

(b) Install the deck trim side panel assembly RH with the screw.





23. INSTALL TONNEAU COVER HOLDER CAP (for RH Side)

HINT
Use the same procedure described for the LH side.

24. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT
Use the same procedure described for the LH side.

25. INSTALL REAR DECK TRIM COVER

(a) Engage the 4 claws and 4 guides to install the rear deck trim cover.





26. INSTALL DECK TRIM SERVICE HOLE COVER

(a) Engage the 3 guides.





(b) Engage the 2 claws to install the deck trim service hole cover.

27. INSTALL REAR NO. 1 FLOOR BOARD

(a) Engage the 2 claws and 2 clips.





(b) Install the rear No. 1 floor board with the bolt.

28. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY

(a) Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.





29. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY

(a) Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.





30. INSTALL DECK FLOOR BOX LH

(a) Engage the 2 guides.





(b) Install the deck floor box LH with the clip.

31. INSTALL REAR NO. 4 FLOOR BOARD

(a) Engage the guide to install the rear No. 4 floor board.





32. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

(a) Install the tonneau cover assembly.

33. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY

(a) Install the upper instrument panel assembly Installation.

34. INSTALL REAR SIDE SEATBACK ASSEMBLY LH Installation

35. INSTALL REAR SIDE SEATBACK ASSEMBLY RH Installation

36. INSTALL REAR SEAT CUSHION ASSEMBLY Installation

37. INSTALL CENTER PILLAR GARNISH LH

(a) Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH.

(b) Engage the clip.





(c) Install the center pillar garnish LH with the screw.

38. INSTALL CENTER PILLAR LOWER GARNISH LH

(a) Engage the 2 claws and 2 clips to install the center pillar lower garnish LH.





39. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH Installation

40. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side) Installation

41. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.





Text in Illustration





NOTICE:
After installation, check that the corners fit correctly.

42. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the 7 claws to install the rear door scuff plate LH.





43. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.





Text in Illustration





(b) Make sure that the front pillar garnish clip is not damaged.





Text in Illustration





NOTICE:
* If there is any damage, replace the garnish clip with a new one.
* When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

(c) Engage the claw to direction indicated by the arrow (1).

(d) Engage the 3 guides to direction indicated by the arrow (2).

(e) Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

HINT
Tape the needle-nosed pliers tip before use.

(f) Engage the 2 clips to install the front pillar garnish LH.





44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.





Text in Illustration





NOTICE:
After installation, check that the corners fit correctly.

45. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Engage the 2 clips.





(b) Install the cowl side trim board LH with the clip.

46. INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the 10 claws to install the front door scuff plate LH.





47. INSTALL CENTER PILLAR GARNISH RH

HINT
Use the same procedure described for the LH side.

48. INSTALL CENTER PILLAR LOWER GARNISH RH

HINT
Use the same procedure described for the LH side.

49. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

50. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT
Use the same procedure described for the LH side.

51. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.





Text in Illustration





NOTICE:
After installation, check that the corners fit correctly.

52. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure described for the LH side.

53. INSTALL FRONT PILLAR GARNISH RH

HINT
Use the same procedure described for the LH side.

54. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.





Text in Illustration





NOTICE:
After installation, check that the corners fit correctly.

55. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

56. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure described for the LH side.

57. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

58. INSTALL REAR NO. 3 FLOOR BOARD

(a) Engage the 2 guides to install the rear No. 3 floor board.





59. INSTALL REAR DECK FLOOR BOX

(a) Install the rear deck floor box.

60. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type)

(a) Engage the 3 guides .





(b) Engage the 2 guides and install the rear No. 2 floor board as shown in the illustration.

61. INSPECT SRS WARNING LIGHT

(a) Inspect the SRS warning light Diagnosis System.

62. ADJUST LANE RECOGNITION CAMERA SENSOR ASSEMBLY (w/ Lane Keeping Assist System) Adjustments
pro multis · About Operation CHARM