Removal

2AZ-FE LUBRICATION: OIL PUMP: REMOVAL; 2013 MY Corolla [07/2012 -]

1. DISCHARGE FUEL SYSTEM PRESSURE Removal

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE FRONT WIPER ARM HEAD CAP Removal

4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH Removal

5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH Removal

6. REMOVE HOOD TO COWL TOP SEAL Removal

7. REMOVE CENTER NO. 1 COWL TOP VENTILATOR LOUVER Removal

8. REMOVE COWL TOP VENTILATOR LOUVER LH Removal

9. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY Removal

10. REMOVE OUTER COWL TOP PANEL Removal

11. REMOVE SUSPENSION TOWER DAMPER ASSEMBLY (w/ Front Strut Bar) Removal

12. REMOVE FRONT WHEEL RH

13. REMOVE ENGINE UNDER COVER LH

14. REMOVE ENGINE UNDER COVER RH

15. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY Removal

16. DRAIN ENGINE COOLANT Service and Repair

17. DRAIN ENGINE OIL Replacement

18. REMOVE CENTER EXHAUST PIPE ASSEMBLY Removal

19. REMOVE FRONT EXHAUST PIPE ASSEMBLY Removal

20. REMOVE V-RIBBED BELT Removal

21. REMOVE GENERATOR ASSEMBLY Removal

22. DISCONNECT NO. 1 RADIATOR HOSE Removal

23. DISCONNECT OUTLET HEATER WATER HOSE Removal

24. DISCONNECT INLET HEATER WATER HOSE Removal

25. SEPARATE RADIATOR RESERVE TANK ASSEMBLY Removal

26. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE Removal

27. REMOVE THROTTLE BODY ASSEMBLY Removal

28. REMOVE IGNITION COIL ASSEMBLY Removal

29. REMOVE SPARK PLUG Removal

30. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY Removal

31. REMOVE ENGINE OIL LEVEL DIPSTICK

32. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE Removal

33. DISCONNECT FUEL MAIN TUBE Removal

34. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY Removal

35. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY Removal

36. REMOVE INTAKE MANIFOLD Removal

37. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR Removal

38. REMOVE MANIFOLD STAY Removal

39. REMOVE NO. 2 MANIFOLD STAY Removal

40. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR Removal

41. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY Removal

42. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH Removal

43. REMOVE IDLER PULLEY SUB-ASSEMBLY Removal

44. REMOVE OIL PAN SUB-ASSEMBLY Removal

45. SET NO. 1 CYLINDER TO TDC / COMPRESSION Removal

46. REMOVE CRANKSHAFT PULLEY Removal

47. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY Removal

48. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY Removal

49. REMOVE CRANK POSITION SENSOR Removal

50. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

(a) Remove the 3 bolts and transverse engine engine mounting bracket.

(b) Using an E10 "TORX" socket, remove the stud bolt for the V-ribbed belt tensioner.

(d) Remove the timing chain cover by prying the portions between the timing chain cover, cylinder head and cylinder block with a screwdriver.

NOTICE:
Be careful not to damage the contact surfaces of the timing chain cover, cylinder head and cylinder block.

HINT
Tape the screwdriver tip before use.

51. REMOVE TIMING CHAIN COVER OIL SEAL

(a) Place the timing chain cover on wooden blocks.

(b) Using a screwdriver, pry out the oil seal.

NOTICE:
Do not damage the surface of the oil seal press fit hole.

HINT
Tape the screwdriver tip before use.

52. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE Removal

53. REMOVE TIMING CHAIN GUIDE Removal

54. REMOVE CHAIN TENSIONER SLIPPER Removal

55. REMOVE NO. 1 CHAIN VIBRATION DAMPER Removal

56. REMOVE CHAIN SUB-ASSEMBLY

57. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET Removal

58. REMOVE NO. 2 CHAIN SUB-ASSEMBLY Removal

59. REMOVE OIL PUMP ASSEMBLY

(a) Remove the 3 bolts, oil pump and gasket.