Installation
WINDOW / GLASS: QUARTER WINDOW GLASS: INSTALLATION
1. CLEAN QUARTER WINDOW ASSEMBLY
(a) Clean the outer edges of the quarter window assembly with a non-residue solvent.
NOTICE:
* Do not touch the glass surface after cleaning it.
* Be careful not to damage the glass or clips.
2. INSTALL QUARTER WINDOW ASSEMBLY
(a) Using a brush or a sponge, apply Primer M to the exposed part of the vehicle body.
Text in Illustration
NOTICE:
* Do not coat the adhesive with Primer M.
* Do not apply too much primer.
* Allow the primer to dry for 3 minutes or more.
* Throw away any leftover primer.
(b) Using a brush or a sponge, apply Primer G to the contact surface of the quarter window glass.
Text in Illustration
HINT
If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.
NOTICE:
* To prevent the glass from breaking at low temperatures, ensure that no primer adheres to the contact surface between the moulding and glass during application.
* Allow the primer to dry for 3 minutes or more.
* Throw away any leftover primer.
* Do not apply too much primer.
(c) Apply adhesive to the quarter window assembly.
Adhesive:
Toyota Genuine Windshield Glass Adhesive or equivalent
(1) Cut off the tip of the cartridge nozzle as shown in the illustration.
Standard Dimension:
(2) Load the sealer gun with cartridge.
(3) Apply adhesive to the quarter window glass as shown in the illustration.
Text in Illustration
(d) Install the quarter window glass to the vehicle body.
(1) Position the quarter window glass so that the matchmarks are aligned, and press it in gently along the rim (when a window with missing clips is used).
Text in Illustration
(2) Lightly press the front surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body (when a window with missing clips is used).
HINT
Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.
(3) Engage the 3 clips to install the quarter window glass (when a window without missing clips is used used).
(4) Hold the quarter window assembly in place securely with protective tape or equivalent until the adhesive hardens.
NOTICE:
* Allow the primer to dry for 3 minutes or more.
* Check that the clips are attached to the body correctly.
* Check the clearance between the body and glass.
(5) Lightly press the outer surface of the glass to ensure that the glass is securely fit to the vehicle body.
(6) Using a scraper, remove any excess or protruding adhesive.
HINT
Apply adhesive onto the glass rim.
NOTICE:
Do not drive the vehicle within the time described in the table below.
Minimum Time:
(e) for RH Side:
(1) Connect each connector.
3. INSPECT FOR LEAK AND REPAIR
(a) After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
(b) If water leaks into the cabin, allow the water to dry and add adhesive.
(c) Remove the protective tape.
4. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY Installation
5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side) Installation
6. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side) Installation
7. INSTALL TONNEAU COVER HOLDER CAP Installation
8. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY Installation
9. INSTALL REAR DECK TRIM COVER Installation
10. INSTALL DECK TRIM SERVICE HOLE COVER Installation
11. INSTALL REAR NO. 1 FLOOR BOARD Installation
12. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY Installation
13. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY Installation
14. INSTALL DECK FLOOR BOX LH (for LH Side) Installation
15. INSTALL REAR NO. 4 FLOOR BOARD (for LH Side) Installation
16. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) Installation
17. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for LH Side) Installation
18. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for RH Side) Installation
19. INSTALL REAR SEAT CUSHION ASSEMBLY Installation
20. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP Installation
21. INSTALL REAR DOOR SCUFF PLATE Installation
22. INSTALL REAR NO. 3 FLOOR BOARD (for RH Side) Installation
23. INSTALL REAR DECK FLOOR BOX Installation
24. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type) Installation