Operation CHARM: Car repair manuals for everyone.
Hosted by mcallihan.com
Home >> Toyota >> 2012 >> Prius L4-1.8L (2ZR-FXE) Hybrid >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Dashboard / Instrument Panel >> Service and Repair >> Removal and Replacement >> Upper Instrument Panel >> Removal

Removal





INTERIOR PANELS / TRIM: UPPER INSTRUMENT PANEL: REMOVAL

1. PRECAUTION

Upper Instrument Panel

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work Service Precautions

2. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type) Removal

3. REMOVE REAR DECK FLOOR BOX Removal

4. REMOVE REAR NO. 3 FLOOR BOARD Removal

5. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

6. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY

(a) Using a moulding remover, slightly lift the panel at the position shown in the illustration.





Text in Illustration





(b) Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

(c) Disconnect each connector and remove the integration control and panel assembly.

7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

(a) Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.





(b) Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.





8. REMOVE INSTRUMENT PANEL CUP HOLDER ASSEMBLY

(a) Remove the 4 screws and instrument panel cup holder assembly from the lower center instrument cluster finish panel sub-assembly.





9. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH

(a) Disengage the 14 claws.

(b) Disconnect the connector and remove the instrument cluster finish panel garnish.





10. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

(a) Disengage the 3 claws.





(b) Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.

11. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

w/ Daytime Running Light: Removal

w/o Daytime Running Light: Removal

12. REMOVE NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type) Removal

13. REMOVE FRONT DOOR SCUFF PLATE LH Removal

14. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH Removal

15. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

(a) Remove the screw .





(b) Disengage the 6 claws and clip as shown in the illustration.





(c) Disengage the claw and 2 guides and disconnect the hood lock control cable.





(d) Disconnect each connector and clamp, and remove the lower instrument panel finish panel assembly.

16. REMOVE NO. 1 INSTRUMENT PANEL REGISTER

(a) Pull the No. 1 instrument panel register in the direction indicated by the arrow to disengage the 2 claws.





(b) Pull the No. 1 instrument panel register in the direction indicated by the arrow to disengage the 2 claws and remove the No. 1 instrument panel register.





17. REMOVE NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL

(a) Disengage the 4 claws to remove the No. 1 center instrument cluster finish panel.





18. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

19. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

(a) Pull the instrument panel finish panel end LH in the direction indicated by the arrow to disengage the 4 claws.





(b) Disengage the guide as shown in the illustration.





(c) Disengage the guide and remove the instrument panel finish panel end LH as shown in the illustration.





20. REMOVE NO. 1 SIDE DEFROSTER NOZZLE

(a) Using a moulding remover, slightly lift the panel at the position shown in the illustration.





Text in Illustration





(b) Pull the No. 1 side defroster nozzle in the direction indicated by the arrow to disengage the 3 claws and remove the No. 1 side defroster nozzle.

21. REMOVE NO. 2 INSTRUMENT PANEL REGISTER

(a) Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the claw and clip.





(b) Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the 2 claws and remove the No. 2 instrument panel register.





22. REMOVE GLOVE COMPARTMENT DOOR

(a) Open the glove compartment door assembly.

(b) Pull the glove compartment door in the direction indicated by the arrow to disengage the 7 claws.





(c) Pull the glove compartment door in the direction indicated by the arrow to remove the glove compartment door.

23. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

24. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

(a) Pull the instrument panel finish panel end RH in the direction indicated by the arrow to disengage the 4 claws.





(b) Disengage the guide as shown in the illustration.





(c) Disengage the guide and remove the instrument panel finish panel end RH as shown in the illustration.





25. REMOVE FRONT PILLAR GARNISH LH Removal

26. REMOVE FRONT PILLAR GARNISH CORNER PIECE LH

(a) Disengage the 3 claws and front pillar garnish corner piece LH as shown in the illustration.





27. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

(a) Pull the No. 1 instrument panel speaker panel sub-assembly in the direction indicated by the arrow to disengage the 6 claws and 2 guides, and remove the No. 1 instrument panel speaker panel sub-assembly.





28. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY Removal

29. REMOVE FRONT PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and LH side Removal.

30. REMOVE FRONT PILLAR GARNISH CORNER PIECE RH

(a) Disengage the 3 claws and front pillar garnish corner piece RH as shown in the illustration.





31. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

(a) Pull the No. 2 instrument panel speaker panel sub-assembly in the direction indicated by the arrow to disengage the 6 claws and 2 guides, and remove the No. 2 instrument panel speaker panel sub-assembly.





32. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

HINT
Use the same procedure for the RH side and LH side Removal.

33. REMOVE INSTRUMENT CLUSTER FINISH PANEL END (w/ Headup Display)

(a) Pull the instrument cluster finish panel end in the direction indicated by the arrow to disengage the 5 claws and 2 guides, and remove the instrument cluster finish panel end





34. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH

(a) Remove the 2 screws .

(b) Disengage the 7 claws.

(c) Disconnect the connector and remove the center instrument cluster finish panel garnish.





35. DISCONNECT NO. 3 INSTRUMENT PANEL WIRE Removal

36. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

(a) Disconnect each connector.

(b) Disengage the 2 clamps.





(c) Remove the 2 bolts .

(d) Remove the 2 passenger airbag bolts .





Text in Illustration





(e) Pull the upper instrument panel assembly in the direction indicated by the arrow to disengage the 2 claws and 4 clips.

(f) Pull the upper instrument panel assembly in the direction indicated by the arrow to disengage the 5 claws and remove the upper instrument panel assembly.




pro multis · About Operation CHARM