Installation

STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION

1. INSPECT STEERING COLUMN ASSEMBLY Testing and Inspection

2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

(a) Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly to install the No. 2 steering intermediate shaft assembly.

Text in Illustration

(b) Install the bolt.

Torque : 35 Nm (359 kgf-cm, 26 ft-lbf)

3. INSTALL STEERING POST ASSEMBLY (for Brush Type Motor)

(a) Install the steering post assembly with the bolt and 2 nuts.

Torque : 25 Nm (255 kgf-cm, 18 ft-lbf)

(b) Connect the connectors and engage the wire harness clamps to the steering post assembly.

(c) Connect the 2 connectors to the power steering ECU assembly.

(d) Engage the 2 wire harness clamps.

4. INSTALL STEERING POST ASSEMBLY (for Brushless Type Motor)

(a) Install the steering post assembly with the bolt and 2 nuts.

Torque : 25 Nm (255 kgf-cm, 18 ft-lbf)

(b) Connect the connectors and engage the wire harness clamps to the steering post assembly.

(c) Connect the connector to the power steering ECU assembly.

(d) Connect the connector to the power steering ECU assembly.

HINT
As shown in the illustration, securely return the lock lever to its original position to connect the connector.

(e) Engage the 2 wire harness clamps.

5. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

(a) Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft to connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft.

Text in Illustration

(b) Install the bolt.

Torque : 35 Nm (357 kgf-cm, 26 ft-lbf)

6. INSTALL COLUMN HOLE COVER SILENCER SHEET

(a) Install the column hole cover silencer sheet with the 2 clips.

(b) Install the floor carpet.

7. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

(a) Engage the 2 claws to install the No. 2 air duct sub-assembly.

8. INSTALL NO. 1 HEATER TO REGISTER DUCT Installation

9. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY

HINT
Refer to the instructions for Installation of the brake pedal support assembly Installation.

10. INSTALL UPPER INSTRUMENT PANEL

HINT
Refer to the instructions for Installation of the upper instrument panel Installation.

11. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY

HINT
Refer to the instructions for Installation of the driver side knee airbag assembly Installation.

12. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

13. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

(a) Using pliers, expand the clamp.

Text in Illustration

(b) While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.

(c) Return the clamp to its original position.

(d) Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

14. INSTALL UPPER STEERING COLUMN COVER

(a) Engage the 2 claws and 2 pins to install the upper steering column cover.

15. INSTALL LOWER STEERING COLUMN COVER

NOTICE:
If the lower steering column cover is installed in the incorrect order, it will not be possible to assemble the lower steering column cover.

(a) Engage the 2 claws to install the lower steering column cover.

(b) Engage the 4 claws.

HINT
Press the area around the claws to engage them.

16. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

17. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY Installation

18. INSTALL STEERING WHEEL ASSEMBLY Installation

19. INSTALL STEERING PAD

HINT
Refer to the instructions for Installation of the steering pad Installation.

20. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Connect the cable to the negative (-) battery terminal with the front wheels facing straight ahead.

22. INSPECT STEERING PAD Installation

23. TORQUE SENSOR ZERO POINT CALIBRATION (for Brush Type Motor)

(a) Perform the torque sensor zero point calibration Power Steering System (For Brush Type Motor).

24. ROTATION ANGLE SENSOR INITIALIZATION AND TORQUE SENSOR ZERO POINT CALIBRATION (for Brushless Type Motor)

(a) Clear the rotation angle sensor calibration value, initialize the rotation angle sensor, and calibrate the torque sensor zero point Power Steering System (For Brushless Type Motor).

25. INSPECT SRS WARNING LIGHT

(a) Inspect the SRS warning light Diagnosis System.