Removal

BRAKE (REAR): REAR BRAKE: REMOVAL

NOTICE:
* When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.
* While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

HINT
* Use the same procedure for the LH side and RH side.
* The following procedure is for the LH side.

1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type) Removal

2. REMOVE REAR DECK FLOOR BOX Removal

3. REMOVE REAR NO. 3 FLOOR BOARD Removal

4. DISABLE BRAKE CONTROL Removal

5. REMOVE REAR WHEEL

6. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately wash it off.

7. REMOVE FRONT DOOR SCUFF PLATE LH Removal

8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH Removal

9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY Removal

10. LOOSEN PARKING BRAKE CABLE

(a) Completely release the parking brake pedal.

(b) Loosen the lock nut and adjusting nut to completely release the parking brake cable.





Text in Illustration





11. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

(a) Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.





(b) Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.





Text in Illustration





HINT
Insert an offset wrench (14 mm) at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip. Pull out the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

12. SEPARATE REAR FLEXIBLE HOSE

(a) Remove the union bolt and gasket, and separate the rear flexible hose from the rear disc brake cylinder assembly.





13. REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

(a) Hold the rear disc brake pad guide pin, and remove the 2 bolts and rear disc brake cylinder assembly.





Text in Illustration





NOTICE:
Remove the rear disc brake cylinder assembly while holding both of the rear disc brake pads because the anti-squeal springs may fall off the rear disc brake pads.

14. REMOVE REAR DISC BRAKE PAD

(a) Remove the 2 anti-squeal springs from the rear disc brake pads.





(b) Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.

15. REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM

(a) Remove the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim from each rear disc brake pad.





Text in Illustration





16. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

(a) Remove the 2 rear disc brake pad support plates from the disc brake cylinder mounting.





NOTICE:
Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be installed to its original position.

17. REMOVE REAR DISC BRAKE PAD GUIDE PIN

(a) Remove the 2 rear disc brake pad guide pins from the rear disc brake cylinder mounting.





18. REMOVE REAR DISC BRAKE BUSHING DUST BOOT

(a) Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.





19. REMOVE REAR DISC BRAKE CYLINDER MOUNTING

(a) Remove the 2 bolts and rear disc brake cylinder mounting from the axle beam.





20. REMOVE REAR DISC

(a) Remove the rear disc.





Text in Illustration





HINT
Place matchmarks on the disc and axle hub.