Reassembly

SEAT: REAR SEAT ASSEMBLY: REASSEMBLY

1. INSTALL BENCH TYPE REAR SEAT CUSHION COVER

(a) Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 14 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

(b) Using hog ring pliers, install 28 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

2. INSTALL REAR SEATBACK LOCK ASSEMBLY LH

(a) Install the rear seatback lock assembly LH to the rear seatback frame sub-assembly LH with the 2 bolts.

Torque : 30 Nm (306 kgf-cm, 22 ft-lbf)

3. INSTALL REAR SEATBACK LOCK RELEASE BUTTON LH

(a) Turn the rear seatback lock release button LH as shown in the illustration to install it to the rear seatback lock assembly LH.

4. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH

(a) Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 9 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

5. INSTALL REAR SEATBACK COVER WITH PAD LH

(a) Temporarily install the rear seatback cover with pad LH to the rear seatback frame sub-assembly LH.

(b) Engage the 4 claws to install the 2 rear seat headrest supports.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

(d) Engage the 6 clips.

(e) Install the 2 clips.

6. INSTALL REAR SEATBACK STOP BUTTON GROMMET

(a) Engage the 3 claws to install the rear seatback stop button grommet.

7. INSTALL REAR SEAT SHOULDER BELT GUIDE LH

(a) Engage the guide to install the rear seat shoulder belt guide LH with the 2 screws.

8. INSTALL REAR SEATBACK COVER LH

(a) Engage the 4 claws to install the rear seatback cover LH.

9. INSTALL REAR SEATBACK LOCK ASSEMBLY RH

(a) Install the rear seatback lock assembly RH to the rear seatback frame sub-assembly RH with the 2 bolts.

Torque : 30 Nm (306 kgf-cm, 22 ft-lbf)

10. INSTALL REAR SEATBACK LOCK RELEASE BUTTON RH

(a) Turn the rear seatback lock release button RH as shown in the illustration to install it to the rear seatback lock assembly RH.

11. INSTALL REAR CENTER SEAT BELT ASSEMBLY Installation

12. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH

(a) Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 9 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

(b) Using hog ring pliers, install 7 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

13. INSTALL REAR SEATBACK COVER WITH PAD RH

(a) Temporarily install the rear seatback cover with pad RH to the rear seatback frame sub-assembly RH.

(b) Engage the 4 claws to install the 2 rear seat headrest supports.

(d) Engage the 4 claws to install the rear seat shoulder belt hole cover as shown in the illustration.

(e) Engage the 2 claws to install the seat belt anchor cover cap.

(f) Using hog ring pliers, install 16 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

(g) Engage the 6 clips.

(h) Install the 3 clips.

14. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Armrest)

(a) Install the bush.

(b) Insert the pin into the rear seatback.

(c) Install the rear seat center armrest assembly with the bolt and bush.

Torque : 6.0 Nm (61 kgf-cm, 53 in-lbf)

15. INSTALL CENTER ARMREST HINGE COVER (w/ Center Armrest)

(a) Engage the claw to install the center armrest hinge cover as shown in the illustration.

16. INSTALL REAR SEATBACK STOP BUTTON GROMMET

(a) Engage the 3 claws to install the rear seatback stop button grommet.

17. INSTALL REAR SEAT SHOULDER BELT GUIDE RH

(a) Engage the guide to install the rear seat shoulder belt guide RH with the 2 screws.

18. INSTALL REAR SEATBACK COVER RH

(a) Engage the 4 claws to install the rear seatback cover RH.

19. INSTALL REAR SEATBACK CENTER COVER

(a) Engage the 4 claws to install the rear seatback center cover.