Audio And Visual System (w/ Daytime Running Light)

AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (w/ Daytime Running Light): DTC CHECK / CLEAR

1. CHECK DTC (CHECK USING TECHSTREAM)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (READY).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

(e) Check for DTCs, and then write them down.

(f) Check the details of the DTC(s) Audio And Visual System (w/ Daytime Running Light).

2. CLEAR DTC (CLEAR USING TECHSTREAM)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (READY).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

(e) Clear the DTCs.

3. START DIAGNOSTIC MODE

HINT
* Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
* Start diagnostic mode 15 seconds after turning the power switch on (READY). Otherwise, some items cannot be checked.

(a) While pressing and holding the "CAR" switch, operate the light control switch: Off -> Tail -> Off -> Tail -> Off -> Tail -> Off.





(b) Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

4. FAILURE DIAGNOSIS

(a) The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.





5. SYSTEM CHECK

(a) The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.





6. CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)

(a) System check mode screen description





Screen Description





*a: Device Name List No. 1 Description





*b: Check Result Description





*e: Device Name List No. 2 Description





(b) Unit check mode screen description





Screen Description





HINT
* This screen is updated once per second.
* A maximum of 6 DTCs can be displayed for history and present DTCs.

(c) Read the system check result.





(1) If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:
A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.

HINT
* When all results are "OK", this means that no DTCs are present.
* When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.

(2) Check the details of the DTC(s) Audio And Visual System (w/ Daytime Running Light).

7. DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)

(a) Clear DTCs





(1) Press the "Memory CLR" switch for 3 seconds.

(2) Confirm that the check results are cleared.

HINT
* To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.
* When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.

(b) Recheck





(1) Press the "Recheck" switch.

(2) Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.





HINT
When DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.

8. FINISH DIAGNOSTIC MODE

(a) Turn the power switch off.