Operation CHARM: Car repair manuals for everyone.
Hosted by mcallihan.com
Home >> Toyota >> 2012 >> Corolla L4-1.8L (2ZR-FE) >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Headliner >> Service and Repair >> Removal

Removal





INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Seat)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

2. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)

3. REMOVE OUTER SEAT TRACK COVER LH (for Manual Seat) Removal

4. REMOVE INNER SEAT TRACK COVER LH (for Manual Seat) Removal

5. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat) Removal

6. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Power Seat)

7. REMOVE OUTER SEAT TRACK COVER LH (for Power Seat) Removal

8. REMOVE INNER SEAT TRACK COVER LH (for Power Seat) Removal

9. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat) Removal

10. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)

11. REMOVE OUTER SEAT TRACK COVER RH (for Manual Seat)

HINT
Use the same procedure as for the LH side Removal.

12. REMOVE INNER SEAT TRACK COVER RH (for Manual Seat)

HINT
Use the same procedure as for the LH side Removal.

13. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

HINT
Use the same procedure as for the LH side Removal.

14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH Removal

15. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH Removal

16. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) Removal

17. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle) Removal

18. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Manual Transaxle) Removal

19. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Automatic Transaxle) Removal

20. REMOVE INSTRUMENT PANEL BOX ASSEMBLY Removal

21. REMOVE FRONT NO. 1 CONSOLE BOX INSERT Removal

22. REMOVE FRONT NO. 2 CONSOLE BOX INSERT Removal

23. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY Removal

24. REMOVE CONSOLE BOX CARPET Removal

25. REMOVE CONSOLE BOX ASSEMBLY (for Manual Transaxle) Removal

26. REMOVE CONSOLE BOX ASSEMBLY (for Automatic Transaxle) Removal

27. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

for C59: Removal

for E351:

28. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

for U250E:

for U341E: Removal

29. REMOVE SHIFT LEVER ASSEMBLY (for Manual Transaxle)

for C59: Removal

for E351:

30. REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY (for Automatic Transaxle)

for U250E:

for U341E: Removal

31. REMOVE INSTRUMENT PANEL FINISH PANEL END LH Removal

32. REMOVE INSTRUMENT PANEL FINISH PANEL END RH Removal

33. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY Removal

34. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY Removal

35. REMOVE COMBINATION METER ASSEMBLY Removal

36. REMOVE FRONT PILLAR GARNISH LH

(a) Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of 2 clips.





HINT
Make the front pillar garnish LH hang down from the front pillar garnish clip.

(b) Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.





NOTICE:
* Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
* Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

HINT
Tape the tips of the needle-nosed pliers before use.

(c) Disengage the 2 guides at the front end of the front pillar garnish LH and remove it.

(d) Protect the curtain shield airbag assembly.





(1) Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and secure the ends of the cover with tape, as shown in the illustration.

NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

37. REMOVE FRONT PILLAR GARNISH RH

HINT
Use the same procedure as for the LH side.

38. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY Removal

39. REMOVE FRONT DOOR SCUFF PLATE LH

(a) Disengage the 8 claws and remove the front door scuff plate LH.





40. REMOVE COWL SIDE TRIM BOARD LH

(a) Disengage the clip and guide, and remove the cowl side trim board LH.





41. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Remove the front door opening trim weatherstrip LH.





42. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY Removal

43. REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY Removal

44. REMOVE FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure as for the LH side.

45. REMOVE COWL SIDE TRIM BOARD RH

HINT
Use the same procedure as for the LH side.

46. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT
Use the same procedure as for the LH side.

47. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY Removal

48. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY Removal

49. REMOVE REAR DOOR SCUFF PLATE LH

(a) Disengage the 6 claws and remove the rear door scuff plate LH.





50. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Remove the rear door opening trim weatherstrip LH.





51. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side) Removal

52. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH Removal

53. REMOVE LOWER CENTER PILLAR GARNISH LH

(a) Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.





54. REMOVE UPPER CENTER PILLAR GARNISH LH

(a) Remove the 2 screws.





(b) Using a clip remover, disengage the clip, and remove the upper center pillar garnish LH.

55. REMOVE REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure as for the LH side.

56. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT
Use the same procedure as for the LH side.

57. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side) Removal

58. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure as for the LH side.

59. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH Removal

60. REMOVE UPPER CENTER PILLAR GARNISH RH

HINT
Use the same procedure as for the LH side.

61. REMOVE SPARE WHEEL COVER Removal

62. REMOVE REAR SEAT HEADREST ASSEMBLY LH

63. REMOVE REAR SEAT HEADREST ASSEMBLY RH

64. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY

65. REMOVE REAR SEAT CUSHION ASSEMBLY Removal

66. REMOVE REAR SEATBACK ASSEMBLY LH Removal

67. REMOVE REAR SEATBACK ASSEMBLY RH Removal

68. REMOVE REAR SEAT SIDE GARNISH LH

(a) Disengage the 2 claws, 2 clips and guide, and remove the rear seat side garnish LH.





69. REMOVE ROOF SIDE INNER GARNISH BOARD LH

(a) Disengage the 2 claws and 2 guides, and remove the roof side inner garnish board LH.





70. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH

(a) Disengage the 4 clips and 2 guides, and remove the roof side inner garnish assembly LH.





71. REMOVE REAR SEAT SIDE GARNISH RH

HINT
Use the same procedure as for the LH side.

72. REMOVE ROOF SIDE INNER GARNISH BOARD RH

HINT
Use the same procedure as for the LH side.

73. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT
Use the same procedure as for the LH side.

74. REMOVE MAP LIGHT ASSEMBLY (w/o Sliding Roof) Removal

75. REMOVE MAP LIGHT ASSEMBLY (w/ Sliding Roof) Removal

76. REMOVE VISOR ASSEMBLY LH

(a) Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.





NOTICE:
Visor bracket cover cannot be reused.

(b) Disengage the 2 clips and remove the visor assembly LH.





(c) Remove the 2 clips from the vehicle body.

77. REMOVE VISOR ASSEMBLY RH

HINT
Use the same procedure as for the LH side.

78. REMOVE ASSIST GRIP SUB-ASSEMBLY

(a) Using a moulding remover, disengage the 4 claws.





NOTICE:
Do not forcibly pry the assist grip covers to prevent them from being deformed.

HINT
Gently pry on the assist grip covers as shown in the illustration to remove them.

(b) Pull off the 2 assist grip covers by hand.

(c) Disengage the 2 clips and remove the assist grip sub-assembly.





(d) Remove the 2 clips from the vehicle body.

HINT
Use the same procedure for the other 3 assist grips.

79. REMOVE NO. 1 ROOM LIGHT ASSEMBLY Removal

80. REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror) Removal

81. REMOVE VISOR HOLDER

(a) Turn the visor holder approximately 45° and pull it out as shown in the illustration.





(b) Disengage the 2 claws and remove the visor holder.

HINT
Use the same procedure for the RH side and LH side.

82. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

(a) Remove the sun roof opening trim moulding.

83. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Disconnect the amplifier antenna assembly connector and disengage each clamp from the front pillar RH.

(b) Disconnect the amplifier antenna assembly connectors and disengage the clamp from the rear pillar RH.

(c) Remove the bolt and disconnect the amplifier antenna assembly from the rear pillar RH.

(d) Disconnect the No. 1 roof wire connector and disengage each clamp from the front pillar LH.

(e) Disconnect the No. 1 roof wire connector from the instrument panel junction block.

(f) Remove the 3 clips.





(g) Remove the roof headlining assembly from the cabin through the front passenger door.





NOTICE:
Do not damage the roof headlining assembly or body interior.

84. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) w/ EC Mirror:

(1) Disconnect the connector.

(b) Disconnect the amplifier antenna assembly connector and disengage each clamp from the front pillar RH.

(c) Disconnect the amplifier antenna assembly connectors and disengage the clamp from the rear pillar RH.

(d) Remove the bolt and disconnect the amplifier antenna assembly from the rear pillar RH.

(e) Disconnect the No. 1 roof wire connector and disengage each clamp from the front pillar LH.

(f) Disconnect the No. 1 roof wire connectors from the instrument panel junction block.

(g) Disconnect the sliding roof drive gear connector.

(h) Remove the 3 clips.





(i) Remove the roof headlining assembly from the cabin through the front passenger door.





NOTICE:
Do not damage the roof headlining assembly or body interior.

85. REMOVE NO. 1 ROOF SILENCER PAD (for TMC Made without Sliding Roof)

(a) Remove the 2 No. 1 roof silencer pads from the roof headlining assembly.





86. REMOVE NO. 1 ROOF SILENCER PAD (for TMMC Made without Sliding Roof)

(a) Remove the 2 No. 1 roof silencer pads from the roof headlining assembly.





87. REMOVE NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Remove the 2 No. 2 roof silencer pads from the roof headlining assembly.





88. REMOVE NO. 3 ROOF SILENCER PAD (for TMC Made without Sliding Roof)

(a) Remove the No. 3 roof silencer pad from the roof headlining assembly.





89. REMOVE ROOF SIDE RAIL SILENCER PAD LH (w/o Sliding Roof)

(a) Remove the roof side rail silencer pad LH from the roof headlining assembly.





90. REMOVE ROOF SIDE RAIL SILENCER PAD RH (w/o Sliding Roof)

HINT
Use the same procedure for the RH side and the LH side.

91. REMOVE ROOF SIDE RAIL SILENCER PAD LH (w/ Sliding Roof)

(a) Remove the roof side rail silencer pad LH from the roof headlining assembly.





92. REMOVE ROOF SIDE RAIL SILENCER PAD RH (w/ Sliding Roof)

HINT
Use the same procedure for the RH side and the LH side.

93. REMOVE AMPLIFIER ANTENNA ASSEMBLY (w/o Sliding Roof) Removal

94. REMOVE AMPLIFIER ANTENNA ASSEMBLY (w/ Sliding Roof) Removal

95. REMOVE NO. 1 ROOF WIRE (for TMC Made without Sliding Roof)

(a) Remove the adhesive tape from the roof headlining assembly.

(b) Remove the No. 1 roof wire from the roof headlining assembly.





96. REMOVE NO. 1 ROOF WIRE (for TMMC Made without Sliding Roof)

(a) Remove the adhesive tape from the roof headlining assembly.

(b) Remove the No. 1 roof wire from the roof headlining assembly.





97. REMOVE NO. 1 ROOF WIRE (w/ Sliding Roof)

(a) Disengage the 3 clamps.

(b) Remove the adhesive tape from the roof headlining assembly.

(c) Remove the No. 1 roof wire from the roof headlining assembly.




pro multis · About Operation CHARM