Operation CHARM: Car repair manuals for everyone.
Hosted by mcallihan.com
Home >> Toyota >> 2012 >> Camry L4-2.5L (2AR-FXE) Hybrid >> Repair and Diagnosis >> Body and Frame >> Seats >> Service and Repair >> Overhaul >> Front Seat Assembly (for Manual Seat) >> Reassembly

Reassembly





SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): REASSEMBLY

1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

(a) Install the separate type front seat cushion spring assembly.

2. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY

(a) Install the 2 front seatback hooks to the separate type front seatback spring assembly.

(b) Engage the 2 guides.





(c) Engage the 4 claws to install the separate type front seatback spring assembly.

3. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY

(a) Install the front seatback frame sub-assembly with the 4 bolts.

Torque : 45 Nm (459 kgf-cm, 33 ft-lbf)

4. INSTALL FRONT SEAT CUSHION PANEL SUB-ASSEMBLY (for Driver Side)

(a) Install the front seat cushion panel sub-assembly with the 4 bolts.

Torque : 10 Nm (102 kgf-cm, 7 ft-lbf)

5. INSTALL RECLINING CONTROL LEVER

(a) Install the reclining control lever with the bolt.

Torque : 15 Nm (153 kgf-cm, 11 ft-lbf)

6. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)

(a) Connect each connector and engage each wire harness clamp to install the front seat wire RH.

7. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side) Installation

8. INSTALL REAR UPPER SEAT TRACK COVER LH (for Front Passenger Side)

(a) Engage the 2 claws to install the rear upper seat track cover LH.

9. INSTALL REAR UPPER SEAT TRACK COVER RH (for Front Passenger Side)

(a) Engage the 2 claws to install the rear upper seat track cover RH.

10. INSTALL FRONT UPPER SEAT TRACK COVER LH

(a) Engage the 2 claws to install the front upper seat track cover LH.

11. INSTALL FRONT UPPER SEAT TRACK COVER RH

(a) Engage the 2 claws to install the front upper seat track cover RH.

12. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)

(a) Engage the 2 claws to install the front seat lower cushion shield LH.





(b) Engage the hook as shown in the illustration.

(c) Install the screw.

Torque : 0.6 Nm (6 kgf-cm, 5 in-lbf)

13. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)

(a) Engage the 2 claws to install the front seat lower cushion shield RH.





(b) Engage the hook as shown in the illustration.

(c) Install the screw.

Torque : 0.6 Nm (6 kgf-cm, 5 in-lbf)

14. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Front Passenger Side)

(a) Engage the 2 claws to install the front seat lower cushion shield LH.

15. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Front Passenger Side)

(a) Engage the 2 claws to install the front seat lower cushion shield RH.

16. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

(a) Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.





NOTICE:
* Be careful not to damage the separate type front seatback cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

(b) Engage the 2 fasteners.

17. INSTALL FRONT SEAT AIRBAG ASSEMBLY Installation

18. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

(a) Temporarily install the separate type front seatback cover with pad.

(b) Engage the 4 claws to install the 2 front seat headrest supports.

(c) Engage the 2 hooks.

CAUTION:
* For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
* Make sure that the strap is not twisted after engaging the 2 hooks.
* Engage the 2 hooks securely.
(1) Slide each hook to engage them.

(2) Install the 4 clips.

(d) Engage the 2 fasteners.

(e) Engage the hook.

19. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

(a) Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 12 new hog rings.





NOTICE:
* Be careful not to damage the separate type front seat cushion cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

20. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

(a) Temporarily install the separate type front seat cushion cover with pad.

(b) Engage each hook.

(c) for Driver Side:

(1) Install the separate type front seat cushion cover.





(d) for Front Passenger Side:

(1) Install the separate type front seat cushion cover.





(e) Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.

21. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) Installation

22. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side) Installation

23. INSTALL FRONT SEAT INNER CUSHION SHIELD

(a) Install front seat inner cushion shield with the 2 screws.

Torque : 0.6 Nm (6 kgf-cm, 5 in-lbf)

24. INSTALL FRONT SEAT CUSHION SHIELD

(a) Engage the 2 claws to install a new front seat cushion shield.

(b) Install the 2 screws.

Torque : 0.6 Nm (6 kgf-cm, 5 in-lbf)

25. CONNECT SEPARATE TYPE FRONT SEATBACK COVER

(a) Connect the 2 rubber bands of the separate type front seatback cover.

26. INSTALL VERTICAL ADJUSTING HANDLE (for Driver Side)

(a) Install the vertical adjusting handle with the screw.

Torque : 0.6 Nm (6 kgf-cm, 5 in-lbf)

27. INSTALL RECLINING ADJUSTER RELEASE HANDLE

(a) Engage the claw to install the reclining adjuster release handle.

28. INSTALL SEAT ADJUSTER COVER CAP

(a) Install the 2 seat adjuster cover caps.
pro multis · About Operation CHARM