Removal

E351 MANUAL TRANSMISSION / TRANSAXLE: MANUAL TRANSAXLE ASSEMBLY: REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE FRONT WIPER ARM HEAD CAP Removal

3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH Removal

4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH Removal

5. REMOVE HOOD TO COWL TOP SEAL Removal

6. REMOVE COWL TOP VENTILATOR LOUVER RH Removal

7. REMOVE COWL TOP VENTILATOR LOUVER LH Removal

8. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY Removal

9. REMOVE OUTER COWL TOP PANEL Removal

10. REMOVE HOOD SUB-ASSEMBLY

(a) Disconnect the 2 washer hose clamps and washer hose.

(b) Remove the 4 bolts and hood sub-assembly.

11. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

12. REMOVE FRONT WHEELS

13. REMOVE ENGINE UNDER COVER LH

14. REMOVE ENGINE UNDER COVER RH

15. DRAIN MANUAL TRANSAXLE OIL Service and Repair

16. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY Removal

17. REMOVE AIR CLEANER CAP SUB-ASSEMBLY Removal

18. REMOVE AIR CLEANER CASE Removal

19. REMOVE BATTERY Removal

20. REMOVE BATTERY CARRIER Removal

21. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

(a) Remove the 2 clips and disconnect the 2 transmission control cables from the control cable bracket*1.

(b) Remove the 2 clips and disconnect the 2 transmission control cables from the transaxle*2.

22. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY

Removal.

23. DISCONNECT WIRE HARNESS AND CONNECTOR

(a) Disconnect the back-up light switch connector and the wire harness clamp and the wire harness.

24. SECURE STEERING WHEEL Removal

25. REMOVE COLUMN HOLE COVER SILENCER SHEET Removal

26. SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY Removal

27. SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY Removal

28. REMOVE CENTER EXHAUST PIPE ASSEMBLY Removal

29. REMOVE FRONT AXLE SHAFT NUT LH Removal

30. REMOVE FRONT AXLE SHAFT NUT RH Removal

31. DISCONNECT FRONT SPEED SENSOR LH Removal

32. DISCONNECT FRONT SPEED SENSOR RH Removal

33. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH Removal

34. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH Removal

35. SEPARATE TIE ROD END SUB-ASSEMBLY LH Removal

36. SEPARATE TIE ROD END SUB-ASSEMBLY RH Removal

37. SEPARATE FRONT LOWER SUSPENSION ARM LH Removal

38. SEPARATE FRONT LOWER SUSPENSION ARM RH Removal

39. SEPARATE FRONT AXLE ASSEMBLY LH Removal

40. SEPARATE FRONT AXLE ASSEMBLY RH Removal

41. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH Removal

42. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH Removal

43. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH Removal

44. INSTALL ENGINE HANGER Removal

45. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY Removal

46. REMOVE CENTER ENGINE MOUNTING MEMBER SUB-ASSEMBLY Removal

47. REMOVE FRONT ENGINE MOUNTING INSULATOR Removal

48. REMOVE STARTER ASSEMBLY Removal

49. DISCONNECT WIRE HARNESS

(a) Remove the nut, and disconnect the the wire harness clamp and wire harness.

50. SUPPORT MANUAL TRANSAXLE ASSEMBLY

(a) Support the manual transaxle with a transmission jack.

51. REMOVE MANUAL TRANSAXLE ASSEMBLY

(a) Remove the bolt and the wire harness clamp bracket.

(b) Remove the through bolt and nut, then separate the engine mounting insulator LH.

NOTICE:
Be careful that the rear side of the engine assembly does not come into contact with the body.

(d) Remove the 3 bolts and the engine mounting bracket LH.

(e) Remove the 6 bolts.

(f) Remove the 4 bolts and the manual transaxle.

52. REMOVE FRONT ENGINE MOUNTING BRACKET

(a) Remove the 3 bolts and the front engine mounting bracket.

53. REMOVE REAR ENGINE MOUNTING INSULATOR Removal

54. REMOVE REAR ENGINE MOUNTING BRACKET

(a) Remove the 3 bolts and the rear engine mounting bracket.

55. REMOVE MANUAL TRANSMISSION CASE PROTECTOR

(a) Remove the 2 bolts and the manual transmission case protector.

56. REMOVE WIRE HARNESS CLAMP BRACKET

(a) Remove the bolt and the wire harness clamp bracket.