B1771
SUPPLEMENTAL RESTRAINT SYSTEM: OCCUPANT CLASSIFICATION SYSTEM: B1771: Passenger Side Buckle Switch Circuit Malfunction
DTC B1771 - Passenger Side Buckle Switch Circuit Malfunction
DESCRIPTION
The passenger side buckle switch circuit consists of the occupant classification ECU and the front seat inner belt assembly RH.
DTC B1771 is recorded when a malfunction is detected in the passenger side buckle switch circuit.
Troubleshoot DTC B1771 first when DTCs B1771 and B1795 are output simultaneously.
*1: w/ Side and curtain shield airbag
*2: w/o Side and curtain shield airbag
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
- If troubleshooting (wire harness inspection) is difficult to perform, remove the front passenger seat installation bolts to see the under surface of the seat cushion.
- In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat only as necessary.
PROCEDURE
1. CHECK DTC
(a) Turn the ignition switch to the ON position.
(b) Clear the DTCs stored in the memory (Reading and Clearing Diagnostic Trouble Codes).
HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position.
(e) Check the DTCs (Reading and Clearing Diagnostic Trouble Codes).
OK:
DTC B1771 is not output.
HINT: Codes other than DTC B1771 may be output at this time, but they are not related to this check.
OK -- USE SIMULATION METHOD TO CHECK
NG -- Continue to next step.
2. CHECK CONNECTION OF CONNECTORS
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery.
(c) Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt assembly RH.
OK:
The connectors are properly connected.
NG -- CONNECT CONNECTORS
OK -- Continue to next step.
3. CHECK WIRE HARNESS (SHORT TO B+)
(a) Disconnect the connectors from the occupant classification ECU and the front seat inner belt assembly RH.
(b) Connect the negative (-) terminal cable to the battery.
(c) Turn the ignition switch to the ON position.
(d) Measure the voltage according to the value(s) in the table below.
Standard voltage:
Result:
C -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE NO. 3
B -- REPAIR OR REPLACE FLOOR WIRE
A -- Continue to next step.
4. CHECK WIRE HARNESS (OPEN)
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery.
(c) Using a service wire, connect B8-2 and B8-1 of connector "C".
NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting.
(d) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Result:
C -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE NO. 3
B -- REPAIR OR REPLACE FLOOR WIRE
A -- Continue to next step.
5. CHECK WIRE HARNESS (SHORT)
(a) Disconnect the service wire from connector "C".
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Result:
C -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE NO. 3
B -- REPAIR OR REPLACE FLOOR WIRE
A -- Continue to next step.
6. CHECK WIRE HARNESS (SHORT TO GROUND)
(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Result:
C -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE NO. 3
B -- REPAIR OR REPLACE FLOOR WIRE
A -- Continue to next step.
7. CHECK DTC
(a) Connect the connectors to the occupant classification ECU and the front seat inner belt assembly RH.
(b) Connect the negative (-) terminal cable to the battery.
(c) Turn the ignition switch to the ON position.
(d) Clear the DTCs stored in the memory (Reading and Clearing Diagnostic Trouble Codes).
HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
(e) Turn the ignition switch to the LOCK position.
(f) Turn the ignition switch to the ON position.
(g) Check the DTCs (Reading and Clearing Diagnostic Trouble Codes).
OK:
DTC B1771 is not output.
HINT: Codes other than DTC B1771 may be output at this time, but they are not related to this check.
OK -- USE SIMULATION METHOD TO CHECK
NG -- Continue to next step.
8. REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery.
(c) Replace the front seat inner belt assembly RH (Removal).
HINT: Perform the inspection using parts from a normal vehicle if possible.
(d) Connect the negative (-) terminal cable to the battery.
(e) Turn the ignition switch to the ON position.
(f) Clear the DTCs stored in the memory (Reading and Clearing Diagnostic Trouble Codes).
HINT: First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
(g) Turn the ignition switch to the LOCK position.
(h) Turn the ignition switch to the ON position.
(i) Check the DTCs (Reading and Clearing Diagnostic Trouble Codes).
OK:
DTC B1771 is not output.
HINT: Codes other than DTC B1771 may be output at this time, but they are not related to this check.
OK -- END
NG -- Continue to next step.
9. REPLACE OCCUPANT CLASSIFICATION ECU
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery.
(c) Replace the occupant classification ECU (Programming and Relearning).
NEXT -- Continue to next step.
10. PERFORM ZERO POINT CALIBRATION
(a) Connect the negative (-) terminal cable to the battery.
(b) Connect Techstream to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Using Techstream, perform "Zero point calibration" (Programming and Relearning).
OK:
"COMPLETED" is displayed.
NEXT -- Continue to next step.
11. PERFORM SENSITIVITY CHECK
(a) Using Techstream, perform "Sensitivity check" (Programming and Relearning).
Standard value:
27 to 33 kg (59.52 to 72.75 lb)
NEXT -- END