Installation

PARKING BRAKE: ELECTRIC PARKING BRAKE ACTUATOR: INSTALLATION

1. APPLY HIGH-TEMPERATURE GREASE Reassembly

2. INSTALL PARKING BRAKE W/BRACKET ACTUATOR ASSEMBLY

(a) Install the actuator with the 3 nuts.

Torque : 18 Nm (184 kgf-cm, 13 ft-lbf)

(b) Install the 3 harness clamps to the member.

Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)

(d) Attach the clamp to the member.

3. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH Reassembly

4. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

5. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH Reassembly

6. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

7. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET LH Reassembly

8. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET RH

HINT
Use the same procedures described for the LH side.

9. INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING

(a) Install the No. 2 parking brake shoe return spring LH and RH.

10. INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING

(a) Connect the parking brake cable.

(1) Apply a thin layer of high-temperature grease to the area where the parking brake shoe lever contacts the parking brake anchor block.

(2) Install the parking brake shoe lever to the parking brake cable.

NOTICE:
Take care to install the correct parking brake shoe lever because the direction of the pin is different between the left and right.

(3) Check that the parking brake inner cable and parking brake shoe lever are securely connected by trying to pull them apart.

(4) Install the parking brake cable to the support bracket with the 2 nuts.

Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)

(5) With the vehicle on the ground, check that the gap between the parking brake cable and drive shaft, and the gap between the parking brake cable and shaft boot are 10 mm (0.394 in.) or more.

HINT
Make sure that the cable is not twisted.

(b) Install the No. 1 parking brake shoe return spring LH and RH.

11. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY Installation

12. TEMPORARILY INSTALL PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH Installation

13. TEMPORARILY INSTALL PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY RH Installation

14. INSTALL REAR DISC LH Reassembly

15. INSTALL REAR DISC RH

HINT
Use the same procedures described for the LH side.

16. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH Reassembly

17. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

18. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY Installation

19. INSTALL TAILPIPE RH Installation

20. INSTALL TAILPIPE LH Installation

21. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH Installation

22. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

23. INSTALL REAR SPEED SENSOR LH Installation

24. INSTALL REAR SPEED SENSOR RH Installation

25. INSTALL ELECTRIC PARKING BRAKE ACTUATOR CAP

(a) Install the actuator cap with the 2 nuts.

Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)

26. INSTALL FLOOR NO. 1 UNDER COVER Installation

27. CONNECT WIRE HARNESS CLAMP

(a) Connect the 2 harness clamps.

28. CONNECT ELECTRIC PARKING ACTUATOR CONNECTOR

(a) Attach the electric parking brake actuator harness grommet.

(b) Connect the trunk interior's parking brake actuator connector.

29. INSTALL REAR WHEEL HOUSE LINER LH Installation

30. INSTALL REAR FLOOR SIDE MEMBER COVER RH Installation

31. INSTALL REAR FLOOR SIDE MEMBER COVER LH Installation

32. INSTALL NO. 5 ROCKER PANEL MOULDING PROTECTOR Installation

33. INSTALL NO. 6 ROCKER PANEL MOULDING PROTECTOR Installation

34. INSTALL NO. 1 DIFFERENTIAL SUPPORT PROTECTOR Installation

35. INSTALL NO. 2 DIFFERENTIAL SUPPORT PROTECTOR Installation

36. INSTALL SEAT VIBRATOR MODULE ASSEMBLY (for Ottoman) Installation

37. CONNECT REAR ACTIVE STABILIZER CONTROL ACTUATOR CONNECTOR (w/ Active Stabilizer System) Installation

38. INSTALL REAR ACTIVE STABILIZER CONTROL ECU ASSEMBLY (w/ Active Stabilizer System) Installation

39. INSTALL BATTERY CARRIER Installation

40. INSTALL BATTERY Installation

41. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH Installation

42. INSTALL REAR FLOOR FINISH PLATE Installation

43. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

44. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER Installation

45. INSTALL NO. 1 COOLER COVER (w/ Rear Air Conditioning System) Installation

46. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY Installation

47. INSTALL DECK TRIM SIDE BOARD RH Installation

48. INSTALL ROPE HOOK ASSEMBLY Installation

49. INSTALL ROPE HOOK Installation

50. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

51. INSTALL BATTERY SERVICE HOLE COVER LH Installation

52. INSTALL SPARE TIRE (w/ Spare Tire)

53. INSTALL TOOL BOX (w/o Spare Tire) Installation

54. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY Installation

55. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

56. STABILIZE SUSPENSION Installation

57. TIGHTEN PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH Installation

58. TIGHTEN PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY RH Installation

59. ADJUST PARKING BRAKE SHOE CLEARANCE

(a) Adjust parking brake shoe clearance Adjustments.

NOTICE:
If the parking brake shoe clearance is not adjusted, the cable end may be damaged.

60. INSTALL REAR WHEEL Installation

61. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

(a) Inspect and adjust the rear wheel alignment Rear Wheel Alignment.

62. INSPECT SPEED SENSOR SIGNAL

(a) Inspect the speed sensor signal Test Mode Procedure.

63. ADJUST VEHICLE HEIGHT

(a) Adjust vehicle height Installation.

64. PERFORM CALIBRATION

(a) Clear the electric parking brake ECU memory and acquire tension sensor zero point Programming and Relearning.

65. PERFORM PARKING BRAKE SHOE BEDDING

(a) Perform parking brake shoe bedding Programming and Relearning.

66. ADJUST HEADLIGHT ASSEMBLY

(a) Adjust headlight assembly (for HID Headlight).

67. ADJUST OBJECT RECOGNITION CAMERA

(a) Adjust object recognition camera Adjustments.

68. INSPECT FOR EXHAUST GAS LEAK Installation