Removal

INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL

REMOVAL

1. REMOVE FRONT SEAT HEADREST ASSEMBLY
2. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH Removal
3. REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH Removal
4. REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH Removal
5. REMOVE REAR INNER SEAT TRACK BRACKET COVER LH Removal
6. REMOVE FRONT SEAT ASSEMBLY LH Removal
7. REMOVE FRONT SEAT HEADREST ASSEMBLY
8. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER RH
HINT: Use the same procedure for the RH side and LH side.

9. REMOVE FRONT INNER SEAT TRACK BRACKET COVER RH
HINT: Use the same procedure for the RH side and LH side.

10. REMOVE REAR OUTER SEAT TRACK BRACKET COVER RH
HINT: Use the same procedure for the RH side and LH side.

11. REMOVE REAR INNER SEAT TRACK BRACKET COVER RH
HINT: Use the same procedure for the RH side and LH side.

12. REMOVE FRONT SEAT ASSEMBLY RH
HINT: Use the same procedure for the RH side and LH side.

13. REMOVE REAR SEAT CUSHION ASSEMBLY Removal
14. REMOVE REAR SEAT HEADREST ASSEMBLY LH
15. REMOVE REAR SEAT HEADREST ASSEMBLY RH
16. REMOVE REAR SEATBACK ASSEMBLY Removal
17. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
18. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

19. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY Removal
20. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH Removal
21. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH Removal
22. REMOVE CONSOLE PANEL SUB-ASSEMBLY Removal
23. REMOVE FRONT ASH RECEPTACLE ASSEMBLY Removal
24. REMOVE REAR ASH RECEPTACLE ASSEMBLY Removal
25. REMOVE CONSOLE BOX REGISTER ASSEMBLY Removal
26. REMOVE CONSOLE BOX Removal
27. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY Removal
28. REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL Removal
29. REMOVE MULTI-DISPLAY WITH RADIO RECEIVER ASSEMBLY (w/ Navigation System) Removal
30. REMOVE INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Navigation System) Removal
31. REMOVE LOWER NO. 3 STEERING WHEEL COVER Removal
32. REMOVE LOWER NO. 2 STEERING WHEEL COVER Removal
33. REMOVE STEERING PAD Removal
34. REMOVE STEERING WHEEL ASSEMBLY Removal
35. REMOVE STEERING COLUMN COVER Removal
36. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY Removal
37. REMOVE FRONT DOOR SCUFF PLATE LH

(a) Put protective tape around the front door scuff plate.
(b) Using a moulding remover, disengage the 4 clips.

(c) Disengage the 7 claws and remove the front door scuff plate LH.
38. REMOVE FRONT DOOR SCUFF PLATE RH
HINT: Use the same procedure for the RH side and LH side.

39. REMOVE FRONT DOOR OPENING TRIM COVER LH

(a) Disengage the 4 claws and remove the front door opening trim cover LH.
40. REMOVE FRONT DOOR OPENING TRIM COVER RH
HINT: Use the same procedure for the RH side and LH side.

41. REMOVE FRONT PILLAR GARNISH LH

(a) Disengage the 2 clips from the vehicle body.
(b) Cut off the clip [A].
(c) Disengage the guide and remove the front pillar garnish LH.
(d) Remove the clip [A] from the vehicle body.

(e) Protect the curtain shield airbag assembly.
(1) Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
NOTE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

42. REMOVE FRONT PILLAR GARNISH RH
HINT: Use the same procedure for the RH side and LH side.

43. REMOVE SIDE INSTRUMENT PANEL LH Removal
44. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Removal
45. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY Removal
46. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY Removal
47. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Removal
48. REMOVE COMBINATION METER ASSEMBLY Removal
49. REMOVE SIDE INSTRUMENT PANEL RH Removal
50. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Removal
51. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY Removal
52. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY Removal
53. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY Removal
54. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY Removal
55. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY Removal
56. REMOVE FRONT STEREO COMPONENT SPEAKER ASSEMBLY (w/ Front Center Speaker) Removal
57. REMOVE NO. 2 CONSOLE BOX DUCT Removal
58. REMOVE NO. 1 CONSOLE BOX DUCT Removal
59. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY Removal
60. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY Removal
61. REMOVE INSTRUMENT PANEL CLIP Removal
62. REMOVE INSTRUMENT PANEL STAY Removal
63. REMOVE NO. 2 FLOOR UNDER COVER Removal
64. REMOVE NO. 1 FLOOR UNDER COVER Removal
65. REMOVE TAIL EXHAUST PIPE ASSEMBLY Removal
66. REMOVE REAR NO. 1 FLOOR PANEL BRACE Removal
67. REMOVE FRONT CENTER FLOOR BRACE Removal
68. DISCONNECT HEATED OXYGEN SENSOR Removal
69. REMOVE FRONT EXHAUST PIPE ASSEMBLY Removal
70. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR Removal
71. REMOVE FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY Removal
72. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY Removal
73. REMOVE REAR DOOR SCUFF PLATE LH

(a) Put protective tape around the rear door scuff plate.
(b) Using a moulding remover, disengage the 2 clips.

(c) Disengage the 5 claws and remove the the rear door scuff plate LH.
74. REMOVE REAR DOOR SCUFF PLATE RH
HINT: Use the same procedure for the RH side and LH side.

75. REMOVE LAP BELT OUTER ANCHOR COVER LH

(a) Disengage the 2 claws and remove the lap belt outer anchor cover LH.
76. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH

(a) Remove the bolt and separate the front seat outer belt assembly LH.
77. REMOVE LOWER CENTER PILLAR GARNISH LH

(a) Disengage the 3 claws and 5 clips, and remove the lower center pillar garnish LH.
78. REMOVE CENTER PILLAR GARNISH LH

(a) Remove the 2 screws.
(b) Disengage the 2 claws and remove the center pillar garnish LH by pulling it down.
79. REMOVE FRONT SEAT BELT ANCHOR COVER SUB-ASSEMBLY

(a) Disengage the 3 claws and remove the front seat belt anchor cover sub-assembly.
80. REMOVE LOWER CENTER PILLAR GARNISH RH
HINT: Use the same procedure for the RH side and LH side.

81. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH

(a) Disconnect the connector.
(b) Remove the bolt and separate the front seat outer belt assembly RH.
82. REMOVE CENTER PILLAR GARNISH RH
HINT: Use the same procedure for the RH side and LH side.

83. REMOVE REAR SEAT SIDE GARNISH LH

(a) Disengage the 5 claws and remove the rear seat side garnish LH.
84. REMOVE REAR SEAT SIDE GARNISH RH
HINT: Use the same procedure for the RH side and LH side.

85. REMOVE ROOF SIDE INNER GARNISH LH

(a) Disengage the 4 clips and claw, and remove the roof side inner garnish LH.
86. REMOVE ROOF SIDE INNER GARNISH RH
HINT: Use the same procedure for the RH side and LH side.

87. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER Removal
88. REMOVE RAIN SENSOR Removal
89. REMOVE MAP LIGHT ASSEMBLY (w/o Sliding Roof) Removal
90. REMOVE MAP LIGHT ASSEMBLY (w/ Sliding Roof) Removal
91. REMOVE SPOT LIGHT ASSEMBLY Removal
92. REMOVE COAT HOOK

(a) Remove the screw and coat hook.
HINT: Use the same procedure to remove the hook on the other side.

93. REMOVE ASSIST GRIP SUB-ASSEMBLY
(a) Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

HINT: Tape the screwdriver tip before use.

(b) Disengage the 2 clips and remove the assist grip sub-assembly.
HINT: Use the same procedure for the other 3 assist grips.

94. REMOVE VISOR BRACKET COVER

(a) Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.
HINT: Use the same procedure to remove the cover on the other side.

95. REMOVE VISOR ASSEMBLY LH

(a) Remove the 2 screws and visor assembly LH.
96. REMOVE VISOR ASSEMBLY RH
HINT: Use the same procedure for the RH side and LH side.

97. REMOVE VISOR HOLDER

(a) Remove the visor holder by turning it counterclockwise.
HINT: Use the same procedure to remove the holder on the other side.

98. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Disconnect the roof wire connector and disengage each clamp from the front pillar LH.
(b) Disconnect each connector from the map light assembly.

(d) Remove the roof headlining assembly from the vehicle through the front right door.
99. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Disconnect the roof wire connector and disengage each clamp from the front pillar LH.
(b) Disconnect each connector from the map light assembly.

(d) Remove the roof headlining assembly from the vehicle through the front right door.
100. REMOVE ROOF HEADLINING PAD

(a) Remove the 2 roof headlining pads.
101. REMOVE NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Remove the No. 1 roof silencer pad.
102. REMOVE CENTER ROOF SILENCER PAD (w/o Sliding Roof)

(a) Remove the center roof silencer pad.
103. REMOVE ROOF HEADLINING PAD LH (w/o Sliding Roof)

(a) Remove the 2 roof headlining pads LH.
104. REMOVE REAR ROOF SILENCER PAD (w/o Sliding Roof)

(a) Remove the 2 rear roof silencer pads.
105. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Sliding Roof)

(a) Remove the rear No. 2 side rail spacer LH.
106. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Sliding Roof)
HINT: Use the same procedure for the RH side and LH side.

107. REMOVE REAR SIDE RAIL SPACER LH (w/ Sliding Roof)

(a) Remove the rear side rail spacer LH.
108. REMOVE REAR SIDE RAIL SPACER RH (w/ Sliding Roof)
HINT: Use the same procedure for the RH side and LH side.

109. REMOVE NO. 2 ROOF HEADLINING PAD

(a) Remove the 2 No. 2 roof headlining pads.
110. REMOVE VANITY LIGHT ASSEMBLY

(a) Disengage the claw [A] and separate the bulb holder from the vanity light, as shown in the illustration.
(b) Disengage the claw [B] and remove the vanity light assembly.
HINT: Use the same procedure to remove the light on the other side.

111. REMOVE NO. 1 ROOF WIRE
(a) Remove the double-sided tape and roof wire.
112. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
113. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
114. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
115. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH