Diagnosis Procedure

FUEL PUMP


Diagnosis Procedure

1.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-I
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Turn ignition switch ON.





4. Check the voltage between ECM harness connector and ground.





Is the inspection result normal?
YES - GO TO 4.
NO - GO TO 2.
2.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-II





Check the voltage between IPDM E/R harness connector and ground.





Is the inspection result normal?
YES - GO TO 3.
NO - GO TO 13.
3.DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors E11, F2
- Harness for open or short between IPDM E/R and ECM
Repair open circuit, short to ground or short to power in harness or connectors.
4.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-II
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Disconnect "fuel level sensor unit and fuel pump (main)" harness connector.
4. Turn ignition switch ON.





5. Check the voltage between "fuel level sensor unit and fuel pump
(main)" harness connector and ground.





Is the inspection result normal?
YES - GO TO 8.
NO - GO TO 5.
5.CHECK 15 A FUSE
1. Turn ignition switch OFF.
2. Disconnect 15 A fuse (No. 81) from IPDM E/R.
3. Check 15 A fuse.
Is the inspection result normal?
YES - GO TO 6.
NO - Replace 15 A fuse.
6.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-III
1. Disconnect IPDM E/R harness connector E8.
2. Check the continuity between IPDM E/R harness connector and "fuel level sensor unit and fuel pump
(main)" harness connector.





3. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES - GO TO 8.
NO - GO TO 7.
7.DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors B4, E106
- Harness connectors B65, B434
- IPDM E/R harness connector E8
- Harness for open or short between IPDM E/R and "fuel level sensor unit and fuel pump (main)"
Repair open circuit or short to power in harness or connectors.
8.CHECK FUEL PUMP GROUND CIRCUIT-I
1. Turn ignition switch OFF.
2. Disconnect dropping resistor harness connector.
3. Check the continuity between "fuel level sensor unit and fuel pump (main)" harness connector and dropping resistor.





4. Also check harness for short to power.
Is the inspection result normal?
YES - GO TO 10.
NO - GO TO 9.
9.DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors B65, B434
- Harness for open or short between "fuel level sensor unit and fuel pump (main)" and dropping resistor
Repair open circuit or short to power in harness or connectors.
10.CHECK FUEL PUMP GROUND CIRCUIT-II
1. Check the continuity between dropping resistor and ground.





2. Also check harness for short to power.
Is the inspection result normal?
YES - GO TO 11.
NO - Repair open circuit or short to power in harness or connectors.
11.CHECK DROPPING RESISTOR
Refer to Component Inspection (Dropping Resistor).
Is the inspecting result normal?
YES - GO TO 12.
NO - Replace dropping resistor.
12.CHECK FUEL PUMP
Refer to Component Inspection (Fuel Pump).
Is the inspection result normal?
YES - GO TO 13.
NO - Replace fuel pump.
13.CHECK INTERMITTENT INCIDENT
Refer to Description.
Is the inspection result normal?
YES - Replace IPDM E/R.
NO - Repair or replace harness or connectors.