Trim Panel: Service and Repair

Interior Trim Removal/Installation - Pillar Areas

Special Tools Required

- KTC Trim Tool Set SOJATP2014
*

A-Pillar Trim

SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.

NOTE:

- Follow the A-pillar trim installation procedure carefully; improper installation could cause the side curtain airbags to deploy improperly and possibly cause injury.
- Put on gloves to protect your hands.
- Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
- Take care not to scratch the trim or the panels.
- The upper clip (A) in the A-pillar trim (B) consists of a plastic grommet (C) and a metal pin (D). The grommet expands when the pin secures it to the body panel (E). The projections (F) on the pin will break during removal, so the upper clip must be replaced with a new one when the trim is reinstalled.





1. Pull the front door opening seal away from the A-pillar as needed Service and Repair.

2. Hit the upper clip (A) in the A-pillar trim (B) with a rubber mallet. The clip is under the "SIDE CURTAIN AIRBAG" mark (C). Hitting the clip breaks the projections (D) on the pin (E) and pushes it into the grommet (F) on the body (G).

NOTE: The upper clip must be replaced with a new one when the A-pillar trim is reinstalled.






3. Pull back the top of the A-pillar trim (A) by hand to remove the upper clip (B) from the body (C).






4. Pull out the A-pillar trim (A) by hand to detach the clips. Pull up the trim from the dashboard (B), then remove the trim.






5. If the side curtain airbag has deployed, replace the A-pillar trim with a new one Service and Repair.

6. If the side curtain airbag has not deployed, check the A-pillar trim (A) and note the following items:

- To prevent the side curtain airbags from deploying improperly and possibly causing injury, inspect the A-pillar trim and replace it with a new one if it has any of these types damage:
- Any cracks, deformations, or stress-whitened areas in the A-pillar trim
- Any cracks or stress-whitened areas in the clip seating surfaces (B)
- Replace the upper clip (C) with a new one.
- If the clips (D) are damaged or stress-whitened, replace them with new ones.





7. Temporarily install the A-pillar trim (Without the upper clip) to check the overlap between the trim and the headliner Service and Repair. Remove the trim and, if necessary, adjust the overlap.

8. Carefully install the new upper clip (A) to the A-pillar trim (B). Be sure that the grommet (C) is nearest to the top of the pin (D) as shown.






9. Reinstall the A-pillar trim (A).

1. Insert the bottom of the trim into the dashboard (B).

2. Place the trim over the A-pillar (C), and fit the upper clip (D), and the lower clips into the holes in the A-pillar, then lightly push the trim into place.

NOTE:

- Make sure the side curtain airbag is not tucked under the clips or the trim ribs.
- Do not push too hard on the A-pillar trim. If you push too hard, the clip will be damaged, and it will not hold the trim properly.
- Gently tug on the A-pillar trim to make sure that all clips are securely fastened.





10. Reinstall the front door opening seal.

B-Pillar Upper/Lower Trim

SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.

NOTE:

- Put on gloves to protect your hands.
- Take care not to bend or scratch the trim or the panels.
- Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.

1. Remove these items:

- Front door sill trim Service and Repair
- Rear door sill trim Service and Repair
- Front door opening seal, as needed Service and Repair
- Rear door opening seal, as needed Service and Repair

2. Slide the front seat forward fully.

3. Remove the B-pillar lower trim (A).

1. Pull back the upper area of the trim to release the upper hooks (B).

2. Detach the lower clips by pulling back the bottom of the trim by hand.





4. Remove the front seat belt lower anchor Front Seat Belt Replacement.

5. Pull back the bottom of the B-pillar upper trim (A) by hand to release the lower hooks (B).






6. Detach the clip by pulling the top of the B-pillar upper trim (A). Pull down the trim to release the upper hooks (B) from the side curtain airbag bracket (C).






7. Pass the front seat belt lower anchor (A) out through a hole in the slider (B), then remove the B-pillar upper trim (C).






8. Remove the slider (A) from the B-pillar upper trim (B).






9. Install the trim in the reverse order of removal, and note these items:

- If the clips (A) are damaged or stress-whitened, replace them with new ones.
- If the side curtain airbag has deployed, replace the B-pillar upper trim (B), the B-pillar lower trim (C), and all the clips on the trim with new parts Service and Repair.
- To prevent the side curtain airbags from deploying improperly and possibly causing injury, inspect the trim and replace it with a new one if it has any of these types of damage:
- Any cracks or deformations in the B-pillar upper trim or the upper hooks (D), or any stress-whitened areas in the upper part of the trim
- Any cracks or deformations in the B-pillar lower trim, or any breakages in the part (E) fitted with the B-pillar upper trim
- Any cracks or stress-whitened areas in the clip seating surfaces (F)
- Replace any damaged parts with new ones.
- Make sure the top of the B-pillar upper trim overlaps with the headliner correctly Service and Repair.
- Make sure the pin (G) on the front seat belt shoulder anchor adjuster (H) and the hole (I) on the back of the slider are engaged when installing the B-pillar upper trim.
- Make sure the upper hooks are installed into the side curtain airbag B-pillar bracket securely.
- Push the clip and the hooks into place securely.
- Before installing the anchor bolt, make sure there are no twists or kinks in the seat belt.

Trim inspection





Slider engagement with shoulder anchor adjuster






C-Pillar Trim

SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.

NOTE:

- Follow the C-pillar trim installation procedure carefully; improper installation could cause the side curtain airbags to deploy improperly and possibly cause injury.
- Put on gloves to protect your hands.
- Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
- Take care not to scratch the trim or the panels.
- The front clip (A) in the C-pillar trim (B) consists of a plastic grommet (C) and a metal pin (D). The grommet expands when the pin secures it to the body panel (E). The projections (F) on the pin will break during removal, so the front clip must be replaced with a new one when the trim is reinstalled.





1. Remove these items:

- Rear seat-back Rear Seat Removal/Installation
- Rear door opening seal, as needed Service and Repair

2. Hit the front clip (A) in the C-pillar trim (B) with a rubber mallet. The clip is near the triangle mark (C). Hitting the clip breaks the projections (D) on the pin (E) and pushes it into the grommet (F) on the body (G).

NOTE: The front clip must be replaced with a new one when the C-pillar trim is reinstalled.






3. Pull back the front of the C-pillar trim (A) by hand to remove the front clip (B) from the body (C).






4. Pull the C-pillar trim (A) by hand to detach the clips and release the hooks (B), then pull out the trim from the rear shelf (C).






5. If the side curtain airbag has deployed, replace the C-pillar trim with a new one Service and Repair.

6. If the side curtain airbag has not deployed, check the C-pillar trim (A) and note the following items:

- To prevent the side curtain airbags from deploying improperly and possibly causing injury, inspect the C-pillar trim and replace it with a new one if it has any of these types of damage:
- Any cracks, deformations, or stress-whitened areas in the C-pillar trim
- Any cracks or stress-whitened areas in the clip seating surfaces (B)
- Replace the front clip (C) with a new one.
- If the clips (D) are damaged or stress-whitened, replace them with new ones.





7. Temporarily install the C-pillar trim (without the front clip) to check the overlap between the trim and the headliner Service and Repair. Remove the trim, and if necessary, adjust the overlap.

8. Carefully install the new front clip (A) to the C-pillar trim (B). Be sure that the grommet (C) is nearest to the top of the pin (D) as shown.






9. Reinstall the C-pillar trim (A).

1. Insert the hooks (B) of the trim into the rear shelf (C).

2. Place the trim over the C-pillar (D), and fit its front clip (E) and the clips into the holes in the C-pillar, then lightly push the trim into place.

NOTE:

- Make sure the side curtain airbag is not tucked under the clips or the trim ribs.
- Do not push too hard on the C-pillar trim. If you push too hard, the clip will be damaged, and it will not hold the trim properly.
- Gently tug on the C-pillar trim to verify that all clips are securely fastened.





10. Reinstall the rear door opening seal.