P
DTC Troubleshooting: B1241 or Indicator P
DTC B1241 or DTC indicator P: A Problem in the Blower Motor Circuit
1. Clear the DTC with the HDS.
2. Turn the ignition switch to LOCK (0), and then turn to ON (II).
3. Do the self-diagnostic with the HDS Initial Inspection and Diagnostic Overview or climate control unit. Initial Inspection and Diagnostic Overview
4. Check for DTCs.
Is DTC B1241 or P indicated?
YES - Go to step 5.
NO - Intermittent failure. Check for loose wires or poor connections on the blower motor circuit.
5. Turn the ignition switch to LOCK (0).
6. Check the No. 9 (40 A) fuse in the under-hood fuse/relay box, and the No. 36 (10 A) fuse in the under-dash fuse/relay box.
Are the fuses OK?
YES - Go to step 7.
NO - Replace the fuses, and recheck. If fuses blow again, check for a short in the No. 9 (40 A) and No. 36 (10 A) fuses circuit.
7. Connect the blower motor 2P connector terminal No. 2 to body ground with a jumper wire.
8. Turn the ignition switch to ON (II).
Does the blower motor run?
YES - Go to step 9.
NO - Go to step 24.
9. Turn the ignition switch to LOCK (0).
10. Disconnect the jumper wire.
11. Disconnect the power transistor 4P connector.
12. Check for continuity between power transistor 4P connector terminal No. 2 and body ground.
Is there continuity?
YES - Go to step 13.
NO - Check for an open in the wire between the power transistor and body ground. If the wire is OK, check for poor ground at G401. Engine Compartment Wire Harness (Left Branch) Connector and Harness Locations
13. Connect power transistor 4P connector terminals No. 2 and No. 4 with a jumper wire.
14. Turn the ignition switch to ON (II).
Does the blower motor run at high speed?
YES - Go to step 15.
NO - Repair open in the wire between the power transistor and the blower motor.
15. Turn the ignition switch to LOCK (0).
16. Disconnect the jumper wire.
17. Disconnect climate control unit connector A (32P).
18. Check for continuity between body ground and climate control unit connector A (32P) terminals No. 13 and No. 14 individually.
Is there continuity?
YES - Repair short to body ground in the wire(s) between the climate control unit and the power transistor.
NO - Go to step 19.
19. Check for continuity between the following terminals of climate control unit connector A (32P) and the power transistor 4P connector.
Is there continuity?
YES - Go to step 20.
NO - Repair open in the wire(s) between the climate control unit and the power transistor.
20. Turn the ignition switch to ON (II).
21. Measure the voltage between body ground and climate control unit connector A (32P) terminals No. 13 and No. 14 individually.
Is there voltage?
YES - Repair short to power in the wires.
NO - Go to step 22.
22. Reconnect climate control unit connector A (32P).
23. Test the power transistor. Blower Power Transistor Test
Is the power transistor OK?
YES - Check for loose wires or poor connections at climate control unit connector A (32P) and at the power transistor 4P connector. If the connections are good, substitute a known-good climate control unit, and recheck. If the symptom/indication goes away, replace the original climate control unit. Climate Control Unit Removal/Installation
NO - Replace the power transistor.
24. Disconnect the jumper wire.
25. Disconnect the blower motor 2P connector.
26. Measure the voltage between the blower motor 2P connector terminal No. 1 and body ground.
Is there battery voltage?
YES - Replace the blower motor.
NO - Go to step 27.
27. Turn the ignition switch to LOCK (0).
28. Remove the blower motor relay from the under-hood fuse/relay box, and test it. Testing and Inspection
Is the relay OK?
YES - Go to step 29.
NO - Replace the blower motor relay.
29. Measure the voltage between blower motor relay 4P socket terminal No. 1 and body ground.
Is there battery voltage?
YES - Go to step 30.
NO - Replace the under-hood fuse/relay box. Under-Hood Fuse/Relay Box Removal and Installation
30. Turn the ignition switch to ON (II).
31. Measure the voltage between blower motor relay 4P socket terminal No. 3 and body ground.
Is there battery voltage?
YES - Go to step 32.
NO - Repair open in the wire between the No. 36 (10 A) fuse in the under-dash fuse/relay box and the blower motor relay.
32. Turn the ignition switch to LOCK (0).
33. Check for continuity between blower motor relay 4P socket terminal No. 4 and body ground.
Is there continuity?
YES - Repair open in the wire between the blower motor relay and the blower motor.
NO - Check for an open in the wire between the blower motor relay and body ground. If the wire is OK, check for poor ground at G301. Engine Compartment Wire Harness (Left Branch) Connector and Harness Locations
