Headliner Replacement (W/CF5)

Headliner Replacement (w/CF5)

Removal Procedure

1. Remove the front bucket seats. Refer to Seat Replacement - Bucket (Seat Replacement - Bucket) in Seats.
2. Remove the center console, if equipped. Refer to Console Replacement - Front Floor (DTS, w/o UV8) (Console Replacement - Front Floor (DTS Without RPO UV8))Console Replacement - Front Floor (DTS with UV8) (Console Replacement - Front Floor (DTS With RPO UV8)) in Instrument Panel, Gages and Console.
3. Remove center seat, if equipped. Refer to Seat Replacement - Center (w/o UV8) (Seat Replacement - Center (Without RPO Code UV8))Seat Replacement - Center (UV8) (Seat Replacement - Center (With RPO Code UV8)) in Seats.
4. Remove the windshield pillar trim. Refer to Garnish Molding Replacement - Windshield Pillar (Garnish Molding Replacement - Windshield Pillar) .
5. Remove the center pillar trim. Refer to Garnish Molding Replacement - Center Pillar.
6. Remove the sail panels. Refer toSail Panel Replacement (Sail Panel Replacement) .

Notice: If the vehicle is equipped with rear vanity mirrors, the rear vanity mirrors must be removed before the removal of the headliner or damage to the roof may result.

7. Remove the rear vanity mirrors, if equipped. Refer to Vanity Mirror Replacement - Rear (Vanity Mirror Replacement - Rear) .
8. Remove the sunshades. Refer to Sunshade Replacement (Sunshade Replacement) .
9. Disconnect the windshield outside moisture sensor electrical connector.
10. Disconnect the rearview mirror electrical connectors.
11. Pull the door opening moldings down to clear headliner.
12. Remove the assist handles. Refer to Assist Handle Replacement (Service and Repair) .




13. Disconnect the headliner wiring harness connector.




14. Open the wire harness retainers and remove the harness.

Notice: Use care when removing or installing the headliner. Excessive bending will damage the headliner.

15. Release the push-in retainers at the rear of the headliner, if equipped.




16. Carefully pull the headliner down in order to release the remaining headliner locators from the roof panel.
17. Remove the headliner through the rear passenger door opening.



Installation Procedure






Important: If the headliner locators separate from the headliner during removal, obtain a locator repair kit from GM SPO.


1. Load the headliner into the vehicle through the rear passenger door opening.
2. With the aid of a helper, raise the headliner into position.
3. Install the assist handles. Refer to Assist Handle Replacement (Service and Repair) .
4. Install the sunshades. Refer to Sunshade Replacement (Sunshade Replacement) .
5. Install the windshield pillar garnish molding. Refer to Garnish Molding Replacement - Windshield Pillar (Garnish Molding Replacement - Windshield Pillar) .
6. Install the center pillar garnish molding. Refer to Garnish Molding Replacement - Center Pillar.




7. Connect the headliner wiring harness connector.




8. Route and secure the wiring harness in the wiring harness retainers to the body.
9. Install the sail panels. Refer to Sail Panel Replacement (Sail Panel Replacement) .
10. Install the rear vanity mirrors, if equipped. Refer to Vanity Mirror Replacement - Rear (Vanity Mirror Replacement - Rear) .

Important: Ensure that the inside lip of the door opening weather-strip is properly seated to close out the headliner, sail panel and pillar garnish moldings.


11. Install the door opening weather-strips in the door openings.
12. Connect the rear view mirror electrical connectors.
13. Connect the windshield outside moisture sensor.
14. Install the center console, if equipped. Refer to Console Replacement - Front Floor (DTS, w/o UV8) (Console Replacement - Front Floor (DTS Without RPO UV8))Console Replacement - Front Floor (DTS with UV8) (Console Replacement - Front Floor (DTS With RPO UV8)) in Instrument Panel, Gages and Console.
15. Install center seat, if equipped. Refer to Seat Replacement - Center (w/o UV8) (Seat Replacement - Center (Without RPO Code UV8))Seat Replacement - Center (UV8) (Seat Replacement - Center (With RPO Code UV8)) in Seats.
16. Install the front bucket seats. Refer to Seat Replacement - Bucket (Seat Replacement - Bucket) in Seats.