Part 4
Mobility Connection Package, C70
INTRODUCTION
- Read through all of the instructions before starting installation.
- Notifications and warning texts are for your safety and to minimize the risk of something breaking during installation.
- Ensure that all tools stated in the instructions are available before starting installation.
- Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.
- In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
Mobility Connection Package
Illustrations A and B
- Remove the protective film on the foam tape and attach as illustrated.
- Connect the USB/iPod connector and the fibre optic cable's connector to the adapter.
- Clamp the USB/iPod cable at the eyelet on the adapters using a cable tie.
- Place the adapter between the carpet and the climate control unit as illustrated.
Note! Do not damage the fibre optic cable.
- Connect the gray connector (1) in the new cable harness to the corresponding socket in the media player.
- Connect the gray connector (2) in the new cable harness to the gray connector (3) which was detached from the media player.
- Plug in the connector (4) on the adapter cable's fibre cable to the media player.
- Plug in the remaining connectors (5) on the fibre optic cable to each other.
- Plug in the remaining connectors that were disconnected from media player.
- Take a 700 mm (27 9/16") long piece of foam tape and cut into three equal pieces. Tape around connectors (2) and (3) and a little around connectors (5).
- Position the connectors to the left in the opening so that they are not in the way when the media player is installed.
- Plug in the remaining connectors that were disconnected to the media player.
- Reinstall the media player and secure it.
- Clean the area on the centre console as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth. Wipe dry carefully, do not rub.
- Allow to dry.
Note! In cases where the area is heavily soiled or treated with cockpit shine, first clean using a washing up detergent.
Only applies to Right-hand vehicles
- Place the control panel cable in the groove as illustrated.
- Remove the protective film on the control panel and press in position as illustrated.
- Press the cable securely into the compartment that is in the joint between the front and rear side of the centre console. Stop level with the lower edge of the display opening.
- Route the cable from the control panel on the right-hand side of the centre console.
- Install the centre console, connect the green connector and fit the screws, two at the top and two on the rear edge.
Applies to cars with manual gearbox
- Install the gear selector boot in the center console starting at the rear edge.
- slide the tunnel console forward so that the locking lug secures it. At the same time, guide in the floor carpet on the left-hand side.
Reinstall:
- the two screws at the front edge of the tunnel console.
- the panel at the parking brake.
- rear tunnel compartment with its screws and cup holder.
- Reinstall the screws.
- Make a mark at the rear of the storage compartment's bottom cover for the USB/iPod cable in the position as shown.
- File two cut-outs at the rear edge of the cover.
- Place the USB/iPod cable in the bottom cover's slot and pres it into place.
Reinstall:
- the ignition control module (ICM) with the connectors, screws and frame.
- front storage compartment inside of the center console.
- Remove the A-pillar panel on the right-hand side.
- Remove the sealing strip.
- Tape a 700 mm (27 9/16")length piece of foam tape on the microphone cable starting 100 mm (4 3/8") from the microphone.
- Clean the microphone and roof panel in the area illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth. Wipe dry carefully, do not rub.
- Allow to dry.
Note! In cases where the area is heavily soiled or treated with cockpit shine, first clean using a washing up detergent.
- Remove the protective film from one side of the Velcro strip and press the Velcro strip onto the microphone.
- Remove the remaining backing tape from the Velcro strip and press the microphone securely onto the ceiling panel as illustrated.
Note! Direct the microphone towards the driver.
- Route the microphone cable on top of the roof panel.
- The microphone cable must be inserted so that it is concealed.