Initiation Fault. Permanent Fault
Initiation fault. Permanent fault
Checking terminals
- Ignition off.
- Disconnect the engine control module (ECM) and DSA control module connectors.
Check the connectors for contact resistance and oxidation according to Checking wiring and terminals. Permanent fault Checking Wiring And Terminals. Permanent Fault.
Remedy as necessary.
Was a fault detected?
Yes - Verification
No - Checking the DSA system
-------------------------------------------------
Checking the DSA system
Faulty signal
Checking the status of the diagnostic trouble code (DTC)
- Ignition off.
- Start and stop the engine a few times.
- Let the engine idle.
Read off diagnostic trouble codes (DTCs).
Is diagnostic trouble code (DTC) DSA-223 still stored?
Yes - Checking the DSA control module
No - Faulty signal. Intermittent fault
------------------------
Checking the DSA control module
- Ignition off.
- Expose the DSA control module.
- Disconnect the DSA control module.
- Connect a new DSA control module alongside.
- Start and stop the engine a few times.
- Let the engine idle.
Read off diagnostic trouble codes (DTCs).
Is diagnostic trouble code (DTC) DSA-223 still stored?
Yes - Replacing the component
No - Replacing the component
------------------------
Replacing the component
The old DSA control module is OK: Reinstall it.
Note! It is vital that any diagnostic trouble codes (DTCs) in the engine control module (ECM) and the DSA control module are remedied before the engine control module (ECM) is replaced.
FENIX 5.1
- Try a new engine control module (ECM)
EMS 2000
- Try a new engine control module (ECM) according to Replacing the engine control module (ECM) Replacing the Engine Control Module (ECM).
Select Continue when the fault has been remedied.
Continue - Verification
------------------------
Replacing the component
The old DSA control module is defective.
Install the new DSA control module according to DSA control module, replacement Service and Repair.
Select Continue when the fault has been remedied.
Continue - Verification
------------------------
Verification
Verification
Verification
Hint: After carrying out the repair, check that the fault has been remedied.
- Ignition off.
- Reconnect the connectors, reinstall components etc.
- DSA control module connected.
- Start and stop the engine a few times.
- Let the engine idle.
Read off diagnostic trouble codes (DTCs).
Is diagnostic trouble code (DTC) DSA-223 still stored?
Yes - VERIFICATION FAILED
No - VERIFIED
------------------------
VERIFICATION FAILED - Fault-tracing information
VERIFIED - FAULT FOUND
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
Do you want to exit fault-tracing?
Yes - FAULT-TRACING FAILED
No - Attempt New Test
------------------------
FAULT-TRACING FAILED - FAULT-TRACING FAILED
Attempt New Test - Checking the status of the diagnostic trouble code (DTC)
-------------------------------------------------
Faulty signal. Intermittent fault
Faulty signal. Intermittent fault
Checking wiring and terminals
Check the DSA control module and engine control module (ECM) connectors for contact resistance and oxidation according to Checking wiring and terminals. Intermittent faults Checking Wiring And Terminals. Intermittent Faults.
Check the cable between DSA control module terminal #1 and the fuse. Check for an intermittent open-circuit according to Checking wiring and terminals. Intermittent faults Checking Wiring And Terminals. Intermittent Faults.
FENIX 5.1
- Check the cable between DSA control module terminal #9 and engine control module (ECM) terminal #31. Check for an intermittent open-circuit according to Checking wiring and terminals. Intermittent faults Checking Wiring And Terminals. Intermittent Faults.
EMS 2000
- Check the cable between DSA control module terminal #9 and ground terminal 31/25. Check for an intermittent open-circuit according to Checking wiring and terminals. Intermittent faults Checking Wiring And Terminals. Intermittent Faults.
Other information
- To connect the breakout box for DSA, see Connecting the breakout box. DSA Connecting The Breakout Box. DSA
- To connect the breakout box for FENIX 5.1, see Connecting the breakout box. FENIX 5.1 Connecting The Breakout Box. FENIX 5.1
- To connect the breakout box for EMS 2000, see Connecting the breakout box. EMS 2000 Connecting The Breakout Box. EMS 2000.
Select Continue when the fault has been remedied.
Continue - Fault-tracing information
------------------------
Fault-tracing information
Information
Fault-tracing information
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
Do you want to view the information again?
Yes - Attempt New Test
No - FAULT FOUND
------------------------
Attempt New Test - Attempt New Test
FAULT FOUND - FAULT FOUND
DONE - DONE
-------------------------------------------------
Attempt New Test - Checking the status of the diagnostic trouble code (DTC)
FAULT FOUND - FAULT FOUND
DONE - DONE
-------------------------------------------------
FAULT-TRACING FAILED - FAULT-TRACING FAILED
FAULT FOUND - FAULT FOUND
DONE - DONE
-------------------------------------------------
Verification
- Ignition off.
- Reconnect the connectors, reinstall components etc.
- Connect VCT 2000.
- Start and stop the engine a few times.
Read off diagnostic trouble codes (DTCs).
Has the diagnostic trouble code (DTC) ECM-91 changed status to intermittent?
Yes - FAULT FOUND
No - No Fault FoundFault-tracing information
-------------------------------------------------
Fault-tracing information
Information
FAULT-TRACING FAILED - FAULT-TRACING FAILED
Attempt New Test - Checking terminals
-------------------------------------------------