Part 3
E351 MANUAL TRANSMISSION / TRANSAXLE: MANUAL TRANSAXLE UNIT: DISASSEMBLY; 2013 MY Corolla [07/2012 -]
40. REMOVE NO. 1 GEAR SHIFT FORK
(a) Remove the No. 1 gear shift fork.
41. REMOVE NO. 3 GEAR SHIFT FORK SHAFT
(a) Remove the No. 3 gear shift fork shaft from the manual transaxle case.
(b) Using 2 screwdrivers and a hammer, remove the 2 shift fork shaft snap rings from the No. 3 gear shift fork shaft.
(c) Remove the reverse shift fork from the No. 3 gear shift fork shaft.
42. REMOVE NO. 2 GEAR SHIFT FORK
(a) Remove the No. 2 gear shift fork from the input shaft assembly.
43. REMOVE INPUT SHAFT ASSEMBLY
(a) Tilt the output shaft, and then remove the input shaft from the manual transaxle case.
44. REMOVE OUTPUT SHAFT ASSEMBLY
(a) Lift the differential case assembly while tilting the output shaft assembly.
(b) Remove the output shaft assembly from the manual transaxle case.
45. REMOVE DIFFERENTIAL CASE ASSEMBLY
(a) Remove the differential case assembly from the manual transaxle case.
46. REMOVE MANUAL TRANSAXLE CASE RECEIVER
(a) Remove the 3 bolts and manual transaxle case receiver from the manual transaxle case.
47. REMOVE INPUT SHAFT FRONT BEARING
(a) Using SST, remove the input shaft front bearing (outer race) from the manual transaxle case.
SST : 09612-65014
09612-01040
09612-01050
48. REMOVE FRONT TRANSAXLE CASE COVER OIL SEAL
(a) Using SST, remove the front transaxle case cover oil seal from the manual transaxle case.
SST : 09612-65014
09612-01040
09612-01050
49. REMOVE OUTPUT SHAFT FRONT BEARING
(a) Using SST, remove the output shaft front bearing (outer race) from the manual transaxle case.
SST : 09387-00041
09387-02020
09387-02010
50. REMOVE OUTPUT SHAFT COVER
(a) Remove the output shaft cover from the manual transaxle case.
51. REMOVE OUTPUT SHAFT REAR BEARING
(a) Using SST and a hammer, remove the output shaft rear bearing from the manual transmission case (outer race).
SST : 09950-60010
09951-00680
SST : 09950-70010
09951-07100
52. REMOVE TRANSMISSION CASE OIL SEAL
(a) Using SST, remove the transmission case oil seal from the manual transmission case.
SST : 09308-00010
53. REMOVE TRANSAXLE CASE OIL SEAL
(a) Using a screwdriver, remove the transaxle case oil seal.
HINT
Tape the screwdriver tip before use to avoid damage.
54. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
(a) Using a brass bar and a hammer, remove the front differential case front tapered roller bearing (outer race) from the manual transaxle case.
(b) Using SST, remove the front differential case front tapered roller bearing from the front differential case.
SST : 09950-00020
SST : 09950-00030
SST : 09950-40011
09957-04010
SST : 09950-60010
09951-00560
55. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
(a) Using SST and a hammer, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear shim from the manual transmission case.
SST : 09950-60020
09951-00790
SST : 09950-70010
09951-07100
(b) Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case.
SST : 09950-60020
SST : 09950-00030
SST : 09950-40011
09957-04010
SST : 09950-60010
09951-00490
56. REMOVE NO. 3 TRANSMISSION HUB SLEEVE
(a) Remove the No. 3 transmission hub sleeve from the No. 3 transmission clutch hub.
57. REMOVE NO. 3 SYNCHROMESH SHIFTING KEY SPRING
(a) Remove the 2 No. 3 synchromesh shifting key springs from the No. 3 transmission clutch hub while pushing on the No. 3 synchromesh shifting key spring.
58. REMOVE SYNCHRONIZER PULL RING
(a) Using a screwdriver, remove the synchronizer pull ring snap ring.
(b) Remove the synchronizer pull ring, No. 5 synchronizer ring outer, No. 5 synchronizer ring inner, and No. 5 synchronizer ring middle from the No. 5 synchronizer ring inner.