Microphone Circuit Between Microphone and Radio Receiver

AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (w/ Multi-display without DVD Player): Microphone Circuit between Microphone and Radio Receiver; 2013 MY Corolla [07/2012 -]
- Microphone Circuit between Microphone and Radio Receiver

DESCRIPTION

* The radio and display receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines (w/o Sliding Roof).

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines (w/ Sliding Roof).

* Using this circuit, the radio and display receiver assembly sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly (w/o Sliding Roof).

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly (w/ Sliding Roof).

WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. CONFIRM MODEL

Result:





B -- CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
A -- Continue to next step.

2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

(a) Disconnect the E129 radio and display receiver assembly connector.

(b) Disconnect the O9 telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

3. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Reconnect the E129 radio and display receiver assembly connector.

(b) Reconnect the O9 telephone microphone assembly connector.

(c) Measure the voltage according to the value(s) in the table below.





Standard Voltage:





(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Removal
OK -- Continue to next step.

4. INSPECT TELEPHONE MICROPHONE ASSEMBLY

(a) Disconnect the O9 telephone microphone assembly connector.

(b) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





NG -- REPLACE TELEPHONE MICROPHONE ASSEMBLY Removal
OK -- Continue to next step.

5. INSPECT TELEPHONE MICROPHONE ASSEMBLY

(a) Reconnect the E129 radio and display receiver assembly connector.

(b) Reconnect the O9 telephone microphone assembly connector.

(c) Turn the ignition switch to ACC.

(d) Connect an oscilloscope to terminals 2 (MIC+) and 4 (MIC-) of the O9 telephone microphone assembly connector.





(e) Check the waveform of the telephone microphone assembly using the oscilloscope.

Result:





Text in Illustration





B -- REPLACE TELEPHONE MICROPHONE ASSEMBLY Removal

A -- END

6. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

(a) Disconnect the E129 radio and display receiver assembly connector.

(b) Disconnect the O10 map light assembly (telephone microphone assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

7. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Reconnect the E129 radio and display receiver assembly connector.

(b) Reconnect the O10 map light assembly (telephone microphone assembly) connector.

(c) Measure the voltage according to the value(s) in the table below.





Standard Voltage:





(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Removal
OK -- Continue to next step.

8. INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

(a) Disconnect the O10 map light assembly (telephone microphone assembly) connector.

(b) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





NG -- REPLACE TELEPHONE MICROPHONE ASSEMBLY
OK -- Continue to next step.

9. INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

(a) Reconnect the E129 radio and display receiver assembly connector.

(b) Reconnect the O10 map light assembly (telephone microphone assembly) connector.

(c) Turn the ignition switch to ACC.

(d) Connect an oscilloscope to terminals 11 (MI1+) and 10 (MIC-) of the O10 map light assembly (telephone microphone assembly) connector.





(e) Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:





Text in Illustration





B -- REPLACE TELEPHONE MICROPHONE ASSEMBLY

A -- PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Problem Symptoms Table

10. REPLACE TELEPHONE MICROPHONE ASSEMBLY

(a) Replace the telephone microphone assembly Removal.

(b) Check if the same malfunction recurs.

Result:





B -- REPLACE MAP LIGHT ASSEMBLY Removal

A -- END