Engine Immobiliser System (for Hatchback)

THEFT DETERRENT / KEYLESS ENTRY: ENGINE IMMOBILISER SYSTEM (for Hatchback): REGISTRATION

1. DESCRIPTION OF CODE REGISTRATION

(a) w/ Wireless Door Lock Control System:

The key has 2 codes: the key code (immobiliser code) and the wireless code. Both of these codes need to be registered. For the wireless code registration procedures, refer to Wireless Door Lock Control System Registration (from 07/2011).

2. KEY REGISTRATION PROCEDURES WHEN ADDING OR REPLACING KEY OR WHEN KEY IS LOST

HINT
* The following procedures require the use of the Techstream:
* - New key code registration
* - Additional key code registration
* - Key code erasure
* A maximum of 5*1 or 8*2 key codes can be registered.
* *1: except for Mexico
* *2: for Mexico

3. PART REPLACEMENT AND KEY REGISTRATION PROCEDURES

(a) The following table shows ECU replacement and key registration procedures for cases in which an ECU has been determined to be malfunctioning during troubleshooting of the engine immobiliser system.

HINT
* The following procedures require the use of the Techstream:
* - New key code registration
* - Additional key code registration
* - Key code erasure
* A maximum of 5*1 or 8*2 key codes can be registered.
* *1: except for Mexico
* *2: for Mexico

4. KEY REGISTRATION (PROCEDURE "A")

(a) New key code registration (Procedure "A"):

NOTICE:
Make sure that no key codes are registered in the transponder key ECU assembly.

HINT
* In this mode, a maximum of 2 key codes for 2 master keys can be registered. The master keys can be registered in any order because the transponder key ECU assembly can distinguish between different types of keys.*1
* In this mode, a maximum of 3 key codes for 2 master keys and 1 sub key can be registered. The master keys and sub key can be registered in any order because the transponder key ECU assembly can distinguish between different types of keys.*2
* New key codes must be registered with the battery connected. The ignition switch can be either ON or off.
* When a new transponder key ECU assembly is installed, key codes must be registered in the transponder key ECU assembly.
* *1: except for Mexico
* *2: for Mexico

Automatic Key Code Registration (New Registration) (except for Mexico)

Automatic Key Code Registration (New Registration) (for Mexico)

HINT
* When the engine immobiliser system is operating normally and the key is pulled out, the theft warning indicator light assembly blinks continuously.
* If the new key code registration fails, code 2-1 will be output through the theft warning indicator light assembly. Trying to re-register an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the maximum limit, code 2-3 will be output through the theft warning indicator light assembly. The output details are shown below.

(b) End automatic key code registration mode:

Automatic key code registration mode can be forced to end when at least 1 key code (immobiliser code) has been registered as the master key.

HINT
Follow the instruction on the Techstream screen to end new key code registration mode.

5. KEY REGISTRATION (PROCEDURE "B")

(a) Additional registration (Procedure "B"):

HINT
* A maximum of 5 master key codes can be registered.*1
* A maximum of 5 master key codes and 3 sub key codes can be registered.*2
* Registration mode will end if any step is not completed within the specified time.
* When the ignition cylinder or the key cylinder set is replaced, remove the transmitter module from the original master key. Then install this transmitter module to a new key and use the new key as the master key. If necessary, use this master key to register other keys.
* *1: except for Mexico
* *2: for Mexico

NOTICE:
When the ignition key cylinder has been replaced, locking and unlocking doors is possible with the new master key transmitter module (removed from the original master key). However, the new master key will not be able to lock and unlock doors through the door key cylinder. Keep the original master key. If the battery in the new master key transmitter module fails, the original master key can be used to lock and unlock doors through the door key cylinder.

Additional Registration

HINT
* A brief outline of a key code registration procedure is shown above. For detailed information, refer to the Techstream screen.
* When the engine immobiliser system is operating normally and the key is pulled out, the theft warning indicator light assembly blinks continuously.
* If the key code registration has failed in automatic key code registration mode, code 2-1 will be output through the theft warning indicator light assembly. Trying to re-register a previous registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the maximum limit, code 2-3 will be output through the theft warning indicator light assembly. The details are shown in procedure "A".

6. KEY REGISTRATION (PROCEDURE "C")

(a) Key code erasure (Procedure "C"):

HINT
* Performing this procedure will erase all key codes except for the master key, which is used for erasing the key codes. In order to use a key whose code has been erased, a new key code must be registered.
* This procedure will be canceled if each step is not completed within the specified time.

Key Code Erasure

HINT
* A brief outline of a key code registration procedure is shown above. For detailed information, refer to the Techstream screen.
* When the engine immobiliser system is operating normally and the key is pulled out, the theft warning indicator light assembly blinks continuously.

8. KEY REGISTRATION (PROCEDURE "E")

(a) ECU communication ID registration (Procedure "E"):

NOTICE:
* When the transponder key ECU assembly is replaced, the ECU communication ID of the ECM must be registered into the transponder key ECU assembly to match their ECU communication IDs.
* The engine cannot be started unless the ECU communication IDs match.
* Do not turn the ignition switch from ON to off 20 times or more before registering the ECU communication ID. Turning the ignition switch from ON to off 20 times or more will result in the engine not starting unless the transponder key ECU assembly is replaced with a new one.
* After registration, turning the ignition switch to the START position may not start the engine on the first try. If so, turn the ignition switch to the START position again.
* After the engine is started, clear DTC B2799 (code for ECM immobiliser communication error) by either of the following:
- Using the Techstream
- Disconnecting the battery for 30 seconds

(1) Using SST, connect terminals TC and CG of the DLC3.

SST : 09843-18040

Text in Illustration

(2) Turn the ignition switch to ON and leave the vehicle as is for 30 minutes.

HINT
Do not start the engine.

(3) Check that the engine starts.

9. KEY REGISTRATION (PROCEDURE "F")

(a) ECU communication ID registration (Procedure "F"):

NOTICE:
The ECU communication ID should be registered when the ECM and transponder key ECU assembly are replaced or when the ECM only is replaced in order to match the ECU communication ID.

ECU Communication ID Registration