Smart Key System (for Entry Function)
THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function): CUSTOMIZE PARAMETERS
1. CUSTOMIZING FUNCTION WITH TECHSTREAM
HINT
The items in the table below can be customized.
NOTICE:
* When the customer requests a change in a function, first make sure that the function can be customized.
* Be sure to make a note of the current setting before customizing.
* When troubleshooting a function, first make sure that the function is set to the default setting.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Customize Setting.
(e) Select the setting by referring to the table below.
Smart Key / Access
HINT
* *1: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected.
* *2: w/ Entry Back Door Open Function
* *3: except for Korea and Mexico
Warning
2. CUSTOMIZING FUNCTION WITH MULTI-DISPLAY
HINT
The items in the table below can be customized.
NOTICE:
* When the customer requests a change in a function, first make sure that the function can be customized.
* Be sure to make a note of the current setting before customizing.
* When troubleshooting a function, first make sure that the function is set to the default setting.
(a) Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (w/o Daytime Running Light))
(1) Turn the power switch on (IG).
(2) Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Setting.
(3) Select the setting by referring to the table below.
* *1: except Korea
* *2: for Korea
(b) Customizing with the multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (w/ Daytime Running Light))
(1) Turn the power switch on (IG).
(2) Enter the following menus: SETUP / Vehicle.
(3) Select the setting by referring to the table below.
* *1: except Korea
* *2: for Korea
3. ENTRY UNLOCK MODE SWITCHING
(a) Check that the power source mode is OFF and the LED on the key is not blinking. Press the LOCK switch and one of the other switches on the key at the same time for approximately 5 seconds while the key is in the detection area.
Driver door unlock default setting:
When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.
NOTICE:
After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.
* Driver door unlock mode:
When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.
* All door unlock mode:
When any touch sensor is touched, all doors unlock.
(b) The certification ECU (smart key ECU assembly) receives this signal from the door control receiver and changes the smart key system to entry unlock mode.
(c) The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer.
HINT
The procedure only changes entry unlock mode of the smart key system. It does not switch the unlocking of the wireless door lock control.
4. ELECTRICAL KEY CANCEL
The electrical key cancel operation disables the following functions:
* Entry Unlock/Lock
* Entry Hybrid Control System Start
* Entry System Back Door Open Function
* Key Lock-in Prevention
* Warning
(a) The operation procedure is as follows:
Precondition:
Power switch off, driver door closed and unlocked.
(1) Push the unlock switch of the key once.
(2) Open the driver door within 5 seconds.
(3) Push the unlock switch of the key twice within 5 seconds.
(4) Close and open the driver door twice within 30 seconds.
(Driver door: Close -> Open -> Close -> Open)
(5) Push the unlock switch of the key twice within 5 seconds.
(6) Close and open the driver door within 30 seconds.
(Driver door: Close -> Open)
(7) Close the driver door within 5 seconds.
When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.