Operation CHARM: Car repair manuals for everyone.
Hosted by mcallihan.com
Home >> Toyota >> 2012 >> Camry L4-2.5L (2AR-FXE) Hybrid >> Repair and Diagnosis >> Transmission and Drivetrain >> Continuously Variable Transmission/Transaxle >> Service and Repair >> Removal and Replacement >> Hybrid Vehicle Transaxle >> Installation

Installation





P314 HYBRID TRANSMISSION / TRANSAXLE: HYBRID VEHICLE TRANSAXLE: INSTALLATION

1. INSTALL NO. 1 INVERTER COOLING HOSE ASSEMBLY

(a) Install the No. 1 inverter cooling hose assembly to the hybrid vehicle transaxle assembly.

2. INSTALL WIRE HARNESS CLAMP BRACKET

(a) Install the 2 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 3 bolts.

Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)

3. INSTALL HYBRID TRANSAXLE MASS DAMPER

(a) Install a new gasket and the hybrid transaxle mass damper.

Torque : 39 Nm (400 kgf-cm, 29 ft-lbf)

4. INSTALL NO. 3 AUTOMATIC TRANSMISSION CASE COVER

(a) Install the No. 3 automatic transmission case cover to the hybrid vehicle transaxle assembly with the 2 bolts and clip.

Torque : 7.0 Nm (71 kgf-cm, 62 in-lbf)

5. INSTALL AUTOMATIC TRANSMISSION CASE COVER

(a) Engage the 2 guides and install the automatic transmission case cover.

6. INSTALL NO. 3 TRANSMISSION CONTROL CABLE BRACKET

(a) Install the No. 3 transmission control cable bracket to the hybrid vehicle transaxle assembly with the bolt.

Torque : 12 Nm (122 kgf-cm, 9 ft-lbf)

7. INSTALL NO. 2 TRANSMISSION CONTROL CABLE BRACKET

(a) Install the No. 2 transmission control cable bracket to the hybrid vehicle transaxle assembly with the bolt.

Torque : 12 Nm (122 kgf-cm, 9 ft-lbf)

8. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

(a) Install the No. 1 transmission control cable bracket to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque : 12 Nm (122 kgf-cm, 9 ft-lbf)

9. INSTALL FRONT ENGINE MOUNTING BRACKET

(a) Install the front engine mounting bracket to the hybrid vehicle transaxle assembly with the 3 bolts.

Torque : 64 Nm (653 kgf-cm, 47 ft-lbf)

10. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

(a) Make sure that the knock pins are installed to the engine.





Text in Illustration





(b) Install the hybrid vehicle transaxle assembly to the engine with the 9 bolts.





NOTICE:
* Do not apply grease either to the spline or to the input shaft.
* Make sure that the wire harness or similar items are not pinched between the contact surfaces.
* Do not forcibly pry on the hybrid vehicle transaxle.
* Make sure to align the hybrid vehicle transaxle so that the input shaft of the hybrid vehicle transaxle will be inserted straight into the inner splines of the transmission input damper.
* When inserting the input shaft of the hybrid vehicle transaxle into the inner splines of the transmission input damper, do not shake the hybrid vehicle transaxle excessively.
* When mounting the hybrid vehicle transaxle to the engine, make sure to securely fit the knock pins into the knock holes.

HINT
Temporarily tighten bolt B first.

11. INSTALL FRONT FRAME ASSEMBLY Installation

12. CONNECT WIRE HARNESS

(a) Connect the 3 clamps and install the motor cable to the hybrid vehicle transaxle assembly with the bolt.

Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)

(b) Connect the 3 clamps, 4 connectors and install the wire harness to the hybrid vehicle transaxle assembly with the 3 bolts.





Bolt A - Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)

Bolt B - Torque : 12 Nm (122 kgf-cm, 9 ft-lbf)

13. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Installation
pro multis · About Operation CHARM