Audio And Visual System (with Intuitive Parking Assist System)

AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Intuitive Parking Assist System): PRECAUTION

1. PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
* After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
* When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following system after the cable is reconnected.






2. PRECAUTIONS FOR RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) A Hard Disk Drive (HDD) is built into the radio and display receiver assembly to store multi-media data, and is used for the audio and visual system. Therefore, care must be taken for the following points when handling:





(1) When it is necessary to replace the navigation ECU sub-assembly, be sure to replace it with a new one.

NOTICE:
If a used navigation ECU sub-assembly is installed as a replacement part, the customer's HDD will not be recognized.

(2) Do not apply any vibration or shock to the radio and display receiver assembly.

NOTICE:
* Do not drop or subject the navigation ECU sub-assembly to severe impacts.
* Do not use the radio and display receiver assembly if it has been dropped or subjected to a severe impact.
* Do not store the radio and display receiver assembly without the HDD installed. (Only remove the HDD from the navigation ECU sub-assembly when the replacement radio and display receiver assembly or HDD is ready.)

(3) Do not remove the radio and display receiver assembly if there is a risk that condensation may occur.

NOTICE:
If the temperature of the radio and display receiver assembly changes rapidly, condensation may occur inside the unit. This may cause a malfunction of the HDD. Therefore, when the radio and display receiver assembly is removed from the instrument panel, it needs to be kept inside the vehicle or in an environment with an equivalent temperature and humidity.

(4) Take measures to prevent static electricity.

NOTICE:
Touching the terminals of a connector can cause static electricity to be transmitted to the internal circuits. This may cause a malfunction of the HDD.

(5) Keep the radio and display receiver assembly away from magnets or magnetized items.

NOTICE:
Keep the radio and display receiver assembly away from speakers, motors, magnetized tools and other magnetic items.

3. PRECAUTIONS FOR HARD DISK DRIVE (HDD)

(a) Multi-media data for the audio and visual system is stored on the Hard Disk Drive (HDD). Make sure to follow the following instructions when replacing the HDD:

NOTICE:
Data downloaded by the customer may be stored on the HDD. This data will be lost when the HDD is replaced. Make sure to warn the customer that their data will be lost and obtain their consent prior to replacing the HDD.

(1) The HDD must only be replaced with a new one. Do not attempt to install a used HDD from another vehicle.

NOTICE:
The navigation ECU sub-assembly can recognize only a new HDD.

(2) Do not touch the HDD cover.





NOTICE:
When removing or installing the HDD, only hold it by the areas shown in the illustration.

(3) Do not apply any vibration or shock to the HDD.

NOTICE:
* Do not drop or subject the HDD to severe impacts.
* Do not use the HDD if it has been dropped or subjected to a severe impact.
* Do not store the HDD by itself if it has been removed from the radio and display receiver assembly. (Only remove the HDD from the radio and display receiver assembly when the replacement navigation ECU sub-assembly or HDD is ready.)

(4) Do not remove the HDD if there is a risk that condensation may occur.

NOTICE:
If the temperature of the HDD changes rapidly, condensation may occur inside the unit. This may cause a malfunction of the HDD. Therefore, when the radio and display receiver assembly is removed from the instrument panel, it needs to be kept inside the vehicle or in an environment with an equivalent temperature and humidity.

(5) Take measures to prevent static electricity.

NOTICE:
Touching the terminals of a connector can cause static electricity to be transmitted to the internal circuits. This may cause a malfunction of the HDD.

(6) Keep the HDD away from magnets or magnetized items.

NOTICE:
Keep the HDD away from speakers, motors, magnetized tools and other magnetic items.

(7) Inspect after HDD replacement.

NOTICE:
Make sure to perform Check Hard Disk Drive in Operation Check to confirm that there are no HDD abnormalities after removal or installation Operation Check.