Part 2

HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM: P0AA6-526, P0AA6-611, P0AA6-612, P0AA6-613, P0AA6-614: Hybrid Battery Voltage System Isolation Fault
P0AA6-614 - Hybrid Battery Voltage System Isolation Fault- (Continued)

10. CHECK HIGH VOLTAGE DIRECT CURRENT AREA

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the connector cover assembly from the inverter with converter assembly.

HINT
Make sure that no foreign objects have entered or contaminated the inverter with converter assembly.

(c) Disconnect connector Q1 of the No. 4 floor wire from the inverter with converter assembly.

HINT
Make sure that no foreign objects have entered or contaminated connector Q1 of the No. 4 floor wire.

(d) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

HINT
Visually inspect the No. 4 floor wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.

NG -- CHECK NO. 4 FLOOR WIRE
OK -- Continue to next step.

11. CHECK NO. 4 ENGINE WIRE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect connector G2 of the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- CHECK NO. 4 ENGINE WIRE

OK -- REPLACE INVERTER WITH CONVERTER ASSEMBLY Components

12. CHECK NO. 4 ENGINE WIRE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect connector G1 of the No. 4 engine wire (air conditioning harness) from the compressor with motor assembly.

Text in Illustration

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE NO. 4 ENGINE WIRE

OK -- AIR CONDITIONING SYSTEM (P0AA6-611) Air Conditioning System

13. CHECK NO. 4 FLOOR WIRE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 4 hybrid battery shield panel Removal.

(c) Disconnect connector Q2 and connector Q3 of the No. 4 floor wire from the hybrid battery junction block assembly.

HINT
Make sure that no foreign objects have entered or contaminated connector Q2 and Q3 of the No. 4 floor wire.

(d) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

HINT
Visually inspect the No. 4 floor wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.

NG -- REPLACE NO. 4 FLOOR WIRE Components

OK -- REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY Components

14. CHECK HV BATTERY

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the hybrid battery junction block assembly Components.

(c) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

NG -- REPLACE HV BATTERY Components

OK -- REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY Components

15. CHECK MOTOR CABLE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the motor cable from the hybrid vehicle transaxle assembly Components.

(c) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE MOTOR CABLE Components

OK -- REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY Components

16. CHECK GENERATOR CABLE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the generator cable from the hybrid vehicle transaxle assembly Components.

(c) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE GENERATOR CABLE Components

OK -- REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY Components

17. CHECK MOTOR CABLE

CAUTION:
Be sure to wear insulated gloves.

(a) Turn the power switch off.

(b) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(c) Disconnect the motor cable from the hybrid vehicle transaxle assembly Components.

(d) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE MOTOR CABLE Components
OK -- Continue to next step.

18. CHECK GENERATOR CABLE

CAUTION:
Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the generator cable from the hybrid vehicle transaxle assembly Components.

(c) Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

Standard Resistance:

Text in Illustration

NG -- REPLACE GENERATOR CABLE Components

OK -- REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY Components