C1380

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM: C1380/64: Stop Light Control Relay Malfunction
C1380/64 - Stop Light Control Relay Malfunction

DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU, the relay contact turns on and the stop lights come on.





WIRING DIAGRAM

Refer to DTC C1249/49 C1249.

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve Initialization.

HINT
When C1249/49 is output together with C1380/64, inspect and repair the trouble areas indicated by C1249/49 first C1249.

PROCEDURE

1. CHECK STOP LIGHT OPERATION

(a) Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:





NG -- INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) How To Proceed With Troubleshooting
OK -- Continue to next step.

2. READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH ASSEMBLY)

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Select the Data List on the Techstream Data List / Active Test.

ABS/VSC/TRAC





(d) Check that the stop light switch assembly condition observed on the Techstream changes according to brake pedal operation.

OK:

The Techstream displays ON or OFF according to brake pedal operation.

NG -- CHECK HARNESS AND CONNECTOR (STP TERMINAL)
OK -- Continue to next step.

3. PERFORM ACTIVE TEST USING TECHSTREAM (STOP LIGHT CONTROL RELAY (STOP RELAY))

(a) Select the Active Test on the Techstream Data List / Active Test.

ABS/VSC/TRAC





(b) Perform the Active Test of the stop light control relay (STOP relay) using the Techstream.

(c) Select the Data List on the Techstream Data List / Active Test.

ABS/VSC/TRAC





(d) Check for stop light control relay (STOP relay) operation using the Data List and stop light operation by performing an Active Test.

Result:





B -- CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
A -- Continue to next step.

4. CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

(a) Turn the power switch off.





(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.

(c) Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)
OK -- Continue to next step.

5. RECONFIRM DTC

(a) Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.

(b) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.

(c) Turn the power switch on (READY).

(d) Perform a road test.

(e) Check if the same DTC is output Reading and Clearing Diagnostic Trouble Codes.

Result:





B -- REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Removal

A -- CHECK FOR INTERMITTENT PROBLEMS How To Proceed With Troubleshooting

6. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Turn the power switch off.





(b) Remove the stop light control relay (STOP relay).

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK -- Continue to next step.

7. INSPECT STOP LIGHT CONTROL RELAY (STOP RELAY)

(a) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration





NG -- REPLACE STOP LIGHT CONTROL RELAY (STOP RELAY)
OK -- Continue to next step.

8. CHECK HARNESS AND CONNECTOR (STP0 TERMINAL)

(a) Install the stop light control relay (STOP relay).





(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

(c) Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

(d) Turn the power switch on (IG).

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (STP0 CIRCUIT)

OK -- REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Removal

9. CHECK HARNESS AND CONNECTOR (STP TERMINAL)

(a) Turn the power switch off.





(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.

(c) Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

OK -- REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Removal