Part 3
U250E AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSAXLE UNIT: REASSEMBLY - (Continued)
50. INSTALL UNDERDRIVE CLUTCH PISTON SET
(a) Coat the underdrive clutch piston with ATF, and install it to the underdrive clutch piston drum.
NOTICE:
* Be careful not to damage the O-ring.
* Be careful not to damage the lip seal of the piston.
51. INSTALL UNDERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY
(a) Install the return spring to the underdrive clutch drum.
NOTICE:
After installing the spring sub-assembly, check all of the springs are fitted in the piston correctly.
(b) Coat the clutch balancer with ATF.
(c) Install the clutch balancer to the underdrive clutch drum.
NOTICE:
Be careful not to damage the lip seal of the clutch balancer.
(d) Place SST on the clutch balancer and compress the piston return spring with a press.
SST : 09350-32014
09351-32070
(e) Using a snap ring expander, install the snap ring to the underdrive clutch drum.
NOTICE:
* Stop the press when the spring seat is lowered 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove. This prevents the spring seat from being deformed.
* Do not expand the snap ring excessively.
(f) Position the end gap of the snap ring in the underdrive clutch drum as shown in the illustration.
NOTICE:
The end gap of the snap ring should not be aligned with any of the stoppers.
52. INSTALL NO. 1 UNDERDRIVE CLUTCH DISC
(a) Coat the 3 discs with ATF.
(b) Install the 3 plates, 3 discs, and flange to the underdrive clutch drum.
NOTICE:
Ensure that the discs, plates, and flange are in the correct order.
53. INSTALL NO. 2 UNDERDRIVE CLUTCH FLANGE HOLE SNAP RING
(a) Using a screwdriver, install the No. 2 underdrive clutch flange hole snap ring.
(b) Check that the end gap of the snap ring is not aligned with one of the cutouts.
NOTICE:
The snap ring should be securely engaged in the groove of the drum.
54. INSTALL UNDERDRIVE CLUTCH ASSEMBLY
(a) Coat the bearing and bearing race with ATF, and install them onto the underdrive clutch.
Bearing And Race Diameter:
(b) Install the underdrive clutch assembly to the transaxle case.
NOTICE:
When installing the underdrive clutch drum sub-assembly, do not damage the oil seal ring.
55. INSTALL PARKING LOCK PAWL
(a) Install the pawl pin and spring to the parking lock pawl.
(b) Temporarily install the parking lock pawl, pin and spring to the transaxle case as shown in the illustration.
56. INSTALL UNDERDRIVE PLANETARY RING GEAR
(a) Install a new snap ring to the outer race of the tapered roller bearing.
HINT
If replacing the bearing, also replace the counter driven gear with a new one.
(b) Using a piston ring compressor, squeeze the snap ring.
(c) Using SST and a press, press in the outer race of the angular ball bearing.
SST : 09950-60020
09951-00890
SST : 09950-70010
09951-07100
NOTICE:
Do not damage the snap ring during installation of the outer race.
(d) Install the underdrive planetary ring gear to the counter driven gear.
(e) Using snap ring pliers, install the snap ring.
57. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY
(a) Using a press, press the angular ball bearing inner race (rear side) into the underdrive planetary gear.
SST : 09726-40010
SST : 09950-60010
09951-00260
SST : 09950-70010
09951-07100
(b) Install the counter driven gear with planetary ring gear to the underdrive planetary gear.
(c) Using SST and a press, press in the angular ball bearing inner race (front side).
SST : 09726-40010
SST : 09950-60010
09951-00260
SST : 09950-70010
09951-07100
NOTICE:
Rotate the counter driven gear while pressing.
(d) Using a press, press in the parking lock gear.
SST : 09316-20011
SST : 09950-60010
09951-00260
SST : 09950-70010
09951-07100
NOTICE:
Rotate the counter driven gear while pressing.
58. INSTALL DIFFERENTIAL DRIVE PINION
(a) Using a press, press in the differential drive pinion.
SST : 09726-40010
SST : 09950-60010
09951-00260
SST : 09950-70010
09951-07100
NOTICE:
Rotate the counter driven gear while pressing.