Part 2
REASSEMBLY - Continued
27. INSTALL MANUAL TRANSMISSION CASE
(a) Apply FIPG to the manual transmission case, as shown in the illustration.
FIPG:
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
NOTE: Parts must be assembled within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.
(b) Install the 13 bolts to the manual transmission side.
Torque: 29 Nm (300 kgf-cm, 22 ft-lbf)
(c) Install the 3 bolts to the transaxle case side.
Torque: 29 Nm (300 kgf-cm, 22 ft-lbf)
28. INSTALL REVERSE IDLER GEAR SHAFT BOLT
(a) Coat the reverse idler gear shaft bolt with sealant, and install it with a new gasket.
Sealant:
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Torque: 29 Nm (300 kgf-cm, 22 ft-lbf)
29. INSTALL LOCK BALL ASSEMBLY NO. 1
(a) Coat the lock ball assembly No. 1 with sealant, and install it using a hexagon wrench.
Sealant:
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Torque: 29 Nm (296 kgf-cm, 21 ft-lbf)
30. INSTALL SHIFT DETENT BALL
(a) Install the 2 shift detent balls, 2 springs, and 2 seats to the manual transmission case.
(b) Coat the 2 shift detent ball plugs with sealant, and install them using a hexagon wrench.
Sealant:
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Torque: 22 Nm (224 kgf-cm, 16 ft-lbf)
(c) Install the shift detent ball, spring and seat to the transaxle case.
(d) Coat the shift detent ball plug with sealant, and install it using a hexagon wrench.
Sealant:
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Torque: 22 Nm (224 kgf-cm, 16 ft-lbf)
31. INSTALL INPUT SHAFT REAR BEARING HOLE SNAP RING
(a) Using a snap ring expander, install the input shaft rear bearing hole snap ring to the input shaft.
32. INSTALL OUTPUT SHAFT REAR BEARING HOLE SNAP RING
(a) Using a snap ring expander, install the output shaft rear bearing hole snap ring to the output shaft.
33. INSTALL SHIFT FORK SHAFT SHAFT SNAP RING
(a) Using a brass bar and a hammer, install the shift fork shaft shaft snap ring to the shift fork shaft No. 2.
34. INSTALL BEARING RETAINER REAR (MTM)
(a) Coat the 5 bolts with sealant, and install them and bearing retainer rear (MTM) to the manual transmission case.
Torque: 27 Nm (279 kgf-cm, 20 ft-lbf)
35. INSTALL 5TH DRIVEN GEAR
(a) Using SST, install the 5th driven gear to the output shaft.
SST: 09309-12020
36. INSTALL 5TH GEAR NEEDLE ROLLER BEARING
(a) Coat the 5th gear needle roller bearing and 5th gear bearing spacer with gear oil, and install them to the input shaft.
37. INSTALL 5TH GEAR
(a) Coat the 5th gear with gear oil, and install it to the input shaft.
38. INSTALL SYNCHRONIZER RING NO. 3
(a) Coat the synchronizer ring No. 3 with gear oil, and install it to the 5th gear.
39. INSTALL TRANSMISSION CLUTCH HUB NO. 3
(a) Install the 3 synchromesh shifting keys and 2 synchromesh shifting key springs to the transmission clutch hub No. 3.
HINT: Do not set the openings of the shifting key springs in the same position.
(b) Using SST and a hammer, install the transmission clutch hub No. 3 to the input shaft.
SST: 09636-20010
- Before driving in the No. 3 clutch hub assembly, place a suitable sized wooden block under the rear side of the input shaft, as shown in the illustration.
- When driving it in, fix the input shaft firmly so that it is not pushed downward. Otherwise the input shaft rear bearing is over loaded and might be damaged.
(c) Select a snap ring from the table below that will make the thrust clearance of the transmission clutch hub No. 3 below 0.1 mm (0.004 in.).
Snap ring thickness:
(d) Using a brass bar and a hammer, install the snap ring to the input shaft.
40. INSPECT 5TH GEAR THRUST CLEARANCE (Transaxle Unit)
41. INSPECT 5TH GEAR RADIAL CLEARANCE (Transaxle Unit)
42. INSTALL GEAR SHIFT FORK NO. 3
(a) Coat the transmission clutch hub sleeve No. 3 with gear oil, and install it and gear shift fork No. 3 to the transmission clutch hub No. 3.
HINT: Do not set the transmission clutch hub No. 3 in an incorrect orientation.
(b) Coat the gear shift lock fork ball with sealant, and install it to the gear shift fork No. 3.
Sealant:
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Torque: 16 Nm (160 kgf-cm, 12 ft-lbf)
43. INSTALL MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT
(a) Engage two gears simultaneously to lock the transmission.
(b) Install a new manual transmission output shaft rear set nut.
Torque: 118 Nm (1,200 kgf-cm, 87 ft-lbf)
(c) Using a chisel and a hammer, stake the manual transmission output shaft rear set nut.
(d) Disengage the two gears.
44. INSTALL MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY
(a) Apply FIPG to the manual transmission case cover sub-assembly as shown in the illustration.
FIPG:
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
NOTE: Parts must be assembled within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.
(b) Install the manual transmission case cover sub-assembly with the 9 bolts to the manual transmission case.
Torque: 18 Nm (185 kgf-cm, 13 ft-lbf)
45. INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY
(a) Coat the 2 bolts with sealant, and install them, 2 bolts, a new gasket and the shift & select lever shaft assembly to the manual transmission case.
Sealant:
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Torque: 20 Nm (200 kgf-cm, 14 ft-lbf)
NOTE: Set the claws of the shift interlock plate into the shift head part of the gear shift fork shaft securely.
46. INSTALL LOCK BALL ASSEMBLY NO. 1
(a) Coat the lock ball assembly No. 1 with sealant, and install it to the manual transmission case.
Sealant:
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Torque: 29 Nm (300 kgf-cm, 22 ft-lbf)
47. INSTALL SELECTING BELL CRANK ASSEMBLY
(a) Install the selecting bell crank assembly and the control shift lever bush with the 2 bolts to the manual transmission case.
Torque: 25 Nm (250 kgf-cm, 18 ft-lbf)
NOTE: Apply MP grease to the inside circumferential surface of the control shift lever bush (A).
48. INSTALL FLOOR SHIFT CONTROL LEVER HOUSING SUPPORT BRACKET
(a) Install the floor shift control lever housing support bracket with the 3 bolts to the transaxle case.
Torque: 18 Nm (184 kgf-cm, 13. ft-lbf)
49. INSTALL BACK UP LIGHT SWITCH ASSEMBLY
(a) Using SST, install the back up light switch assembly with a new gasket to the manual transmission case.
Torque: 40 Nm (411 kgf-cm, 30 ft-lbf)
SST: 09817-16011
50. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
(a) Install a new O-ring to the speedometer driver hole cover sub-assembly.
(b) Install the speedometer driver hole cover sub-assembly with the bolt.
Torque: 11 Nm (115 kgf-cm, 8 ft-lbf)
51. INSTALL SPEEDOMETER SENSOR
(a) Install a new O-ring to the speedometer sensor.
(b) Install the speedometer sensor with the bolt.
Torque: 11 Nm (115 kgf-cm, 8 ft-lbf)
52. INSTALL RELEASE FORK SUPPORT
(a) Install the clutch release fork support to the transaxle case.
Torque: 37 Nm (375 kgf-cm, 27 ft-lbf)
53. INSTALL CLUTCH RELEASE FORK BOOT
(a) Install the clutch release fork boot to the transaxle case.
54. INSTALL CLUTCH RELEASE BEARING ASSEMBLY
(a) Coat the clutch release bearing assembly with release hub grease, and install it to the clutch release fork sub-assembly with the release bearing clip.
Grease:
Toyota Genuine Release Hub Grease or equivalent
55. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY
(a) Install the clutch release fork sub-assembly to the input shaft.
(b) Apply clutch spline grease to the spline of the input shaft.
Grease:
Toyota Genuine Clutch Spline Grease or equivalent
56. INSTALL MANUAL TRANSMISSION FILLER PLUG
(a) Install the manual transmission filler plug with a new gasket.
Torque: 39 Nm (400 kgf-cm, 29 ft-lbf)
57. INSTALL DRAIN (MTM) PLUG SUB-ASSEMBLY
(a) Install the drain (MTM) plug sub-assembly with a new gasket.
Torque: 39 Nm (400 kgf-cm, 29 ft-lbf)