Part 3

A245E AUTOMATIC TRANSAXLE: AUTOMATIC TRANSAXLE UNIT: DISASSEMBLY

DISASSEMBLY CONTINUED

56. REMOVE COUNTER DRIVE GEAR BEARING
(a) Remove the snap ring from the counter drive gear bearing.
(b) Remove the counter drive gear bearing from the counter drive gear.
57. REMOVE COUNTER DRIVEN GEAR

(a) Using a chisel and hammer, unstake the counter driven gear nut.

(b) Using SST to hold the counter shaft assembly, remove the counter driven gear nut on the counter driven gear side.
SST: 09350-32014
09351-32170

(d) Remove the thrust needle roller bearing from the transaxle case.
58. REMOVE COUNTER SHAFT ASSEMBLY

(a) Pull out the counter shaft assembly from the transaxle case.

(b) Remove the thrust needle roller bearing from the counter shaft assembly.
59. INSPECT PISTON STROKE OF UNDERDRIVE CLUTCH (Transaxle Unit)

60. REMOVE UNDERDRIVE CLUTCH ASSEMBLY

(a) Remove the underdrive clutch assembly from the transaxle case.
61. REMOVE UNDERDRIVE 1 WAY CLUTCH RETAINER
(a) Remove the underdrive 1 way clutch retainer from the transaxle case.
62. INSPECT UNDERDRIVE 1 WAY CLUTCH ASSEMBLY (Transaxle Unit)

63. REMOVE UNDERDRIVE 1 WAY CLUTCH ASSEMBLY

(a) Remove the underdrive 1 way clutch assembly and underdrive clutch drum thrust washer from the underdrive clutch drum sub-assembly.
64. REMOVE OVERDRIVE CLUTCH DRUM OIL SEAL RING

(a) Remove the 2 overdrive clutch drum oil seal rings from the transaxle case.
65. INSPECT PACK CLEARANCE OF UNDERDRIVE BRAKE (Transaxle Unit)

66. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC

(a) Using SST and a press, press in the flange until the snap ring is free from the flange.
SST: 09350-32014
09351-32070
(b) Using a screwdriver, remove the No. 2 underdrive clutch flange hole snap ring from the transaxle case.

(c) Remove the flange, 3 plates and 3 discs.
67. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC (Transaxle Unit)

68. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

(a) Remove the underdrive brake return spring sub-assembly from the transaxle case.
69. REMOVE UNDERDRIVE BRAKE PISTON

(a) Using low-pressure compressed air (98 kPa, 1 kgf/cm2, 14 psi), pop out the underdrive brake piston into a rag.

(b) Using a screwdriver, remove the 2 O-rings from the underdrive brake piston.
70. REMOVE PARKING LOCK PAWL

(a) Remove the 2 bolts, pawl stopper plate, torsion spring and spring guide sleeve from the transaxle case.

(b) Remove the bolt and pawl shaft clamp from the transaxle case.

(a) Remove the spring guide sleeve from the transaxle case.
72. REMOVE CAM GUIDE SLEEVE

(a) Remove the cam guide sleeve from the transaxle case.
73. REMOVE B-4 ACCUMULATOR PISTON

(a) Using a "TORX" wrench, remove the 7 screws.

(b) Remove the 2 bolts.
(c) Remove the No. 2 transmission case plate and No. 2 transmission case plate gasket from the transaxle case.

(d) Remove the B-4 accumulator piston and compression spring from the transaxle case.
(e) Remove the O-ring from the B-4 accumulator piston.
74. REMOVE NO. 3 TRANSMISSION CASE PLATE
(a) Remove the bolt and No. 3 transmission case plate from the transaxle case.
75. REMOVE COUNTER DRIVEN GEAR CYLINDRICAL ROLLER BEARING

(a) Using SST, remove the counter driven gear cylindrical roller bearing from the transaxle case.
SST: 09308-00010
76. REMOVE NO. 1 TRANSAXLE APPLY TUBE CLAMP

(a) Remove the 2 bolts and 2 clamps from the transaxle housing.
77. REMOVE NO. 2 TRANSAXLE APPLY TUBE CLAMP
(a) Remove the bolt and No. 2 transaxle apply tube clamp from the transaxle housing.
78. REMOVE TRANSMISSION LUBE APPLY TUBE

(a) Using a screwdriver, remove the transmission lube apply tube from the transaxle housing.

HINT: Tape the screwdriver tip before use.

NOTE: Be careful not to bend or damage the tube.

79. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE
(a) Using a screwdriver, remove the differential gear lube apply tube transaxle housing.

HINT: Tape the screwdriver tip before use.

NOTE: Be careful not to bend or damage the tube.

80. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING

(a) Remove the bolt, seal washer and roller bearing retainer from the transaxle housing.

(b) Using SST, remove the underdrive cylindrical roller bearing from the transaxle housing.
SST: 09308-00010
81. REMOVE TRANSAXLE HOUSING OIL SEAL

(a) Using a screwdriver, remove the transaxle housing oil seal from the transaxle housing.
82. REMOVE TRANSAXLE CASE OIL SEAL

(a) Using a screwdriver, remove the transaxle case oil seal from the transaxle case.
83. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

(a) Setting SST to the cut-out portion on the speedometer drive gear, remove the front drive pinion front tapered roller bearing from the differential case.
SST: 09950-40011
09951-04010
09952-04010
09953-04030
09954-04010
09955-04061
09957-04010
09958-04011
SST: 09950-60010
09951-00340
(b) Remove the speedometer drive gear from the differential case.

(c) Using SST and a hammer, drive out the front drive pinion front tapered roller bearing outer race.
SST: 09350-32014
09351-32090
84. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

(a) Setting SST to the cut-out portion on the differential case, remove the front drive pinion rear tapered roller bearing from the differential case.
SST: 09950-40011
09951-04010
09952-04010
09953-04030
09954-04010
09955-04061
09957-04010
09958-04011
SST: 09950-60010
09951-00410

(b) Using SST and a hammer, drive out the front drive pinion rear tapered roller bearing outer race and plate washer.
SST: 09350-32014
09351-32130
09351-32150
85. BEARING POSITION
(a) Check the bearing position.