Headliner: Service and Repair

ROOF HEADLINING

Roof Headlining:

Roof Headlining:

Roof Headlining:

Roof Headlining:

REMOVAL

HINT: A bolt without a torque specification is shown in the standard bolt chart.

1. REMOVE FRONT DOOR SCUFF PLATE RH
a. Using a screwdriver, remove the front door scuff plate RH.





HINT: Tape the screwdriver tip before use.

2. REMOVE FRONT DOOR SCUFF PLATE LH
3. REMOVE REAR DOOR SCUFF PLATE RH
a. Using a screwdriver, remove the rear door scuff plate RH.





HINT: Tape the screwdriver tip before use.

4. REMOVE REAR DOOR SCUFF PLATE LH
5. REMOVE COWL SIDE TRIM BOARD RH
a. Remove the clips.
b. Using a screwdriver, remove the cowl side trim board RH.





HINT: Tape the screwdriver tip before use.

6. REMOVE COWL SIDE TRIM BOARD LH
7. REMOVE FRONT DOOR OPENING TRIM RH
8. REMOVE FRONT DOOR OPENING TRIM LH
9. REMOVE REAR DOOR OPENING TRIM RH
10. REMOVE REAR DOOR OPENING TRIM LH
11. REMOVE CENTER PILLAR GARNISH LOWER RH
a. Pull the center pillar garnish lower RH upward to remove it.





12. REMOVE CENTER PILLAR GARNISH LOWER LH
13. REMOVE CENTER PILLAR GARNISH RH
a. Using a screwdriver, remove the shoulder anchor cover cap.





HINT: Tape the screwdriver tip before use.

b. Remove the bolt and front seat outer belt shoulder anchor.
c. Remove the bolt and front seat outer belt floor anchor.
d. Using a screwdriver, remove the center pillar upper garnish RH.





HINT: Tape the screwdriver tip before use.

14. REMOVE CENTER PILLAR GARNISH LH
15. REMOVE REAR SEAT CUSHION ASSEMBLY
16. REMOVE REAR SEATBACK ASSEMBLY (for Separate Seat Type)
17. REMOVE REAR SEATBACK ASSEMBLY (for Bench Seat Type)
18. REMOVE REAR SEAT SIDE COVER RH
a. Using a screwdriver, remove the rear seat side cover RH.





HINT: Tape the screwdriver tip before use.

19. REMOVE REAR SEAT SIDE GARNISH LH
20. REMOVE ROOM PARTITION BOARD LH (for Separate Seat Type)
a. Remove the 2 clips, 2 built-in clips and room partition board LH.





21. REMOVE ROOM PARTITION BOARD RH (for Separate Seat Type)
a. Remove the clip, 2 built-in clips and room partition board RH.

22. REMOVE ROOF SIDE GARNISH INNER RH
a. Using a screwdriver, remove the roof side garnish inner RH.





HINT: Tape the screwdriver tip before use.

23. REMOVE ROOF SIDE GARNISH INNER LH
24. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
a. Using a clip remover, remove the 7 clips.
b. Pull out the belt from the slit and then remove the package tray trim panel.





25. REMOVE FRONT PILLAR GARNISH RH
a. Using a screwdriver, remove the front pillar garnish RH.





HINT: Tape the screwdriver tip before use.

26. REMOVE FRONT PILLAR GARNISH LH
27. REMOVE VISOR ASSEMBLY RH
a. Remove the 2 screws and RH visor.





28. REMOVE VISOR ASSEMBLY LH
29. REMOVE MAP LIGHT ASSEMBLY (with SLIDING ROOF)
a. Remove the screw.
b. Using a screwdriver, remove the map light lens and cover.

HINT: Tape the screwdriver tip before use.

c. Remove the screw.
d. Using a screwdriver, remove the map light.

HINT: Tape the screwdriver tip before use.





30. REMOVE NO. 1 INTERIOR LIGHT ASSEMBLY
a. Using a screwdriver, remove the lens cover.

HINT: Tape the screwdriver tip before use.

b. Using a screwdriver, remove the No. 1 interior light as shown in the illustration.

HINT: Tape the screwdriver tip before use.





31. REMOVE ASSIST GRIP SUB-ASSEMBLY
a. Using a screwdriver, remove the 2 assist grip covers.
b. Remove the 2 screws and assist grip.





32. REMOVE VISOR HOLDER
a. Remove the visor holder by turning it counterclockwise.





33. REMOVE SUN ROOF OPENING TRIM MOULDING (with SLIDING ROOF)
34. REMOVE ROOF HEADLINING ASSEMBLY
a. Remove the 3 clips and roof headlining.





INSTALLATION

1. INSTALL ROOF HEADLINING ASSEMBLY
a. Align the wire harness to the markings, and then attach the wire harness with tape.
b. Attach the roof wire harness with tape.

NOTICE: Roof wire harness should be attached securely.

c. Install the 3 clips.





2. INSTALL ROOM PARTITION BOARD RH (for Separate Seat Type)
3. INSTALL ROOM PARTITION BOARD LH (for Separate Seat Type)
4. INSTALL REAR SEAT SIDE COVER RH (for Bench Seat Type)
5. INSTALL REAR SEAT SIDE GARNISH LH (for Bench Seat Type)
6. INSTALL REAR SEATBACK ASSEMBLY (for Bench Seat Type)
7. INSTALL REAR SEATBACK ASSEMBLY (for Separate Seat Type)