Seals and Gaskets: Service and Repair
DIFFERENTIAL OIL SEALCOMPONENTS (Part 1):
COMPONENTS (Part 2):
REMOVAL
1. DRAIN AUTOMATIC TRANSAXLE FLUID
2. REMOVE FRONT WHEEL
3. REMOVE FRONT AXLE HUB NUT LH
4. REMOVE FRONT AXLE HUB NUT RH
HINT: Use the same procedures described for the LH side.
5. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH
6. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
7. SEPARATE FRONT SPEED SENSOR LH
8. SEPARATE FRONT SPEED SENSOR RH
9. SEPARATE TIE ROD ASSEMBLY LH
10. SEPARATE TIE ROD ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
11. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM LH
12. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM RH
HINT: Use the same procedures described for the LH side.
13. SEPARATE FRONT AXLE ASSEMBLY LH
14. SEPARATE FRONT AXLE ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
15. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
16. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
17. FIX FRONT AXLE ASSEMBLY LH
18. FIX FRONT AXLE ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
19. REMOVE TRANSAXLE HOUSING OIL SEAL
(a) Using SST, pull out the oil seal.
SST 09308-00010
20. REMOVE DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL
(a) Using SST, pull out the oil seal.
SST 09308-00010
INSTALLATION
1. INSTALL TRANSAXLE HOUSING OIL SEAL
(a) Using SST and a hammer, install a new oil seal.
SST 09316-60011 (09316-00011)
Oil seal installation depth: -0.5 to 0.5 mm (-0.020 to 0.020 inch)
(b) Coat the lip of the oil seal with MP grease.
2. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL
(a) Using SST and a hammer, install a new oil seal.
SST 09649-17010, 09950-70010 (09951-07150)
Oil seal installation depth: -0.5 to 0.5 mm (-0.020 to 0.020 inch)
(b) Coat the lip of the oil seal with MP grease.
3. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
4. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
5. INSTALL FRONT AXLE ASSEMBLY LH
6. INSTALL FRONT AXLE ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
7. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM LH
8. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM RH
HINT: Use the same procedures described for the LH side.
9. INSTALL TIE ROD ASSEMBLY LH
10. INSTALL TIE ROD ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
11. INSTALL FRONT SPEED SENSOR LH
12. INSTALL FRONT SPEED SENSOR RH
HINT: Use the same procedures described for the LH side.
13. INSTALL FRONT STABILIZER LINK ASSEMBLY LH
14. INSTALL FRONT STABILIZER LINK ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
15. INSTALL FRONT AXLE HUB NUT LH
16. INSTALL FRONT AXLE HUB NUT RH
HINT: Use the same procedures described for the LH side.
17. INSTALL FRONT WHEEL
18. ADD AUTOMATIC TRANSAXLE FLUID
19. INSPECT AUTOMATIC TRANSAXLE FLUID
20. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT.
21. CHECK ABS SPEED SENSOR SIGNAL