Front Seat Assembly (For Manual Seat)
DISASSEMBLYNOTICE: Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
1. REMOVE VERTICAL ADJUSTER COVER LH (for Driver Seat)
a. Using a screwdriver, disengage the 2 claws and remove the vertical adjuster cover LH.
HINT: Tape the screwdriver tip before use.
2. REMOVE VERTICAL ADJUSTING HANDLE NO. 2 (for Driver Seat)
a. Remove the 2 screws and vertical adjusting handle.
3. REMOVE RECLINING ADJUSTER RELEASE HANDLE
a. Lift the reclining adjuster release handle.
b. Using a screwdriver, disengage the claw and remove the reclining adjuster release handle.
HINT: Tape the screwdriver tip before use.
4. REMOVE FRONT SEAT CUSHION SHIELD
a. Disengage the 2 hooks.
b. Remove the 3 screws.
c. Disengage the 2 claws and remove the front seat cushion shield.
5. REMOVE LOWER SEAT TRACK SPACER
a. Remove the 2 screws and lower seat track spacer.
6. REMOVE FRONT SEAT INNER BELT ASSEMBLY
7. REMOVE FRONT INNER SEAT CUSHION SHIELD
a. Remove the screw.
b. Disengage the claw and clip, and then remove the front inner seat cushion shield.
8. REMOVE FRONT SEAT CUSHION COVER WITH PAD
a. Disengage the clamp.
b. Disengage the hooks and remove the front seat cushion cover with pad.
9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
a. Remove the 16 hog rings and separate type front seat cushion cover.
10. REMOVE FRONT SEAT BACK BOARD SUB-ASSEMBLY
a. Remove the 2 screws.
b. Disconnect the 14 clamps and front separate type seat back cover.
c. Pull the seat back board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seat back board.
11. REMOVE FRONT SEAT HEADREST SUPPORT
a. Detach the 2 claws and remove the headrest support.
12. REMOVE FRONT SEAT HEADREST SUPPORT
13. REMOVE FRONT SEAT BACK COVER WITH PAD
a. Disengage the 3 hooks.
b. Remove the 2 hog rings.
c. Remove the nut and separate the 2 brackets.
d. Remove the front seat back cover with pad.
14. REMOVE FRONT SEPARATE TYPE SEAT BACK COVER
a. Remove the 10 hog rings and front separate type seat back cover.
15. REMOVE RECLINING ADJUSTER INSIDE COVER LH
a. Disconnect the clamp.
b. Remove the screw.
c. Disengage the claw and remove the reclining adjuster inside cover LH.
16. REMOVE RECLINING ADJUSTER INSIDE COVER RH
HINT: Use the same procedures for the RH side and LH side.
17. REMOVE RECLINING ADJUSTER INSIDE COVER LH
a. Remove the screw and reclining adjuster inside cover LH.
18. REMOVE RECLINING ADJUSTER INSIDE COVER RH
HINT: Use the same procedures for the RH side and LH side.
19. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH
a. Using a screwdriver, disengage the claw and remove the front lower seat cushion shield LH.
20. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH
HINT: Use the same procedures for the RH side and LH side.
21. REMOVE SEAT POSITION SENSOR (for Driver Seat)
REASSEMBLY
NOTICE: Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
1. INSTALL SEAT POSITION SENSOR (for Driver Side)
2. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH
3. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH
4. INSTALL RECLINING ADJUSTER INSIDE COVER LH
5. INSTALL RECLINING ADJUSTER INSIDE COVER RH
6. INSTALL RECLINING ADJUSTER INSIDE COVER LH
7. INSTALL RECLINING ADJUSTER INSIDE COVER RH
8. INSTALL FRONT SEPARATE TYPE SEAT BACK COVER
a. Using hog ring pliers, install the front separate type seat back cover to the front separate type seat back pad with 10 new hog rings.
NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
9. INSTALL FRONT SEAT BACK COVER WITH PAD
a. Fully cover the airbag with the 2 seat back cover brackets and tighten the nut.
Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)
NOTICE:
- For vehicles with side airbags, the seat back cover must be securely installed. Otherwise, the side airbags may not deploy properly.
- Make sure that the strap is not twisted after installing the bracket.
- Install the bracket securely.
b. Using hog ring pliers, install the seat back cover (with pad) to the seat frame with 2 new hog rings, and attach the hooks.
c. Engage the 3 hooks.
10. INSTALL FRONT SEAT HEADREST SUPPORT
11. INSTALL FRONT SEAT HEADREST SUPPORT
12. INSTALL FRONT SEAT BACK BOARD SUB-ASSEMBLY
13. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
a. Using hog ring pliers, install the separate type front seat cushion cover to the seat back pad with 16 new hog rings.
NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
14. INSTALL FRONT SEAT CUSHION COVER WITH PAD
15. INSTALL FRONT INNER SEAT CUSHION SHIELD
16. INSTALL FRONT SEAT INNER BELT ASSEMBLY
17. INSTALL LOWER SEAT TRACK SPACER
18. INSTALL FRONT SEAT CUSHION SHIELD (for Driver Seat)
19. INSTALL RECLINING ADJUSTER RELEASE HANDLE
20. INSTALL VERTICAL ADJUSTING HANDLE NO. 2 (for Driver Seat)
21. INSTALL VERTICAL ADJUSTER COVER LH (for Driver Seat)