Front Seat Assembly (For Manual Seat)

Front Seat Assembly (for Manual Seat):

DISASSEMBLY

1. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH
2. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
a. Using a screwdriver, pry out the reclining adjuster release handle RH.

HINT: Tape the screwdriver tip before use.

3. REMOVE FRONT SEAT CUSHION SHIELD RH
a. Remove the screw and the front seat cushion shield RH.

4. REMOVE FRONT SEAT CUSHION SHIELD INNER RH
a. Remove the screw and the front seat cushion shield inner RH.

5. REMOVE SEAT CUSHION COVER WITH PAD
a. Disengage the hook and remove the 2 clips and the seat cushion cover together with the pad.

6. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
a. Remove the hog rings and separate type front seat cushion cover.

7. REMOVE FRONT SEAT HEADREST ASSEMBLY
8. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY RH
a. Remove the 2 screws.
b. Disengage the 2 claws and remove the front seatback board sub-assembly RH.

9. REMOVE SEPARATE TYPE FRONT SEATBACK COVER
a. Disengage the hooks and remove the separate type front seatback cover.

10. REMOVE FRONT SEAT HEADREST SUPPORT
a. Disengage the 2 claws and remove the front seat headrest support (LH side).

11. REMOVE FRONT SEAT HEADREST SUPPORT

HINT: Use the same procedures for the RH side and LH side.

12. REMOVE SEATBACK COVER WITH PAD
a. Remove the 2 nuts and disconnect the separate type front seatback cover bracket.
b. Remove the seatback cover with pad.

13. REMOVE SEPARATE TYPE FRONT SEATBACK COVER
a. Remove the hog rings and the separate type front seatback cover.

14. REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER
a. Remove the screw and the RH seat reclining adjuster inside cover.

15. REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER

HINT: Use the same procedures for the RH side and LH side.

16. REMOVE RECLINING ADJUSTER INSIDE COVER RH
a. Remove the screw and the reclining adjuster inside cover RH.

17. REMOVE RECLINING ADJUSTER INSIDE COVER LH

HINT: Use the same procedures for the RH side and LH side.

18. REMOVE OCCUPANT CLASSIFICATION ECU
19. REMOVE FRONT SEAT WIRE RH

REASSEMBLY

1. INSTALL OCCUPANT CLASSIFICATION ECU
2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
a. Install the seatback pad.
b. Cover the top of the seatback pad with the separate type front seatback cover.

c. Using hog ring pliers, install the separate type front seatback cover to the seatback pad with new hog rings.

NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.

3. INSTALL SEATBACK COVER WITH PAD
a. Install the seatback cover with pad.
b. Install the separate type front seatback cover bracket with the 2 nuts.

Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)

c. Using hog ring pliers, install the separate type front seatback cover.

NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.

d. Engine the hooks.

4. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
a. Install the front seat cushion pad to the seat cushion cover.

b. Using hog ring pliers, install the separate type front seat cushion cover to the seat cushion pad with new hog rings.

NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.

5. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH