Monitors, Trips, Drive Cycles and Readiness Codes
Drive CyclePROCEDURE
There are seven drive patterns of drive cycles A - G for the trouble diagnosis. Performing the specified drive pattern allows to diagnose malfunctioning items listed below. After the malfunctioning items listed below are repaired, always check if they correctly resume their functions by performing the required drive pattern.
1. PREPARATION FOR THE DRIVE CYCLE
1. Make sure that the fuel remains approx. half amount [20 � 40 2 (5.3 � 10.6 US gal, 4.4 � 8.8 Imp gal)], and battery voltage is 12 V or more.
2. Disconnect the test mode connector.
NOTE:
- Except for the engine coolant temperature specified items at starting, the diagnosis is carried out after engine warm up.
- Carry out the diagnosis which is marked* on DTC twice, then, after finishing first diagnosis, stop the engine and do second time at the same condition.
P0125 - P2103:
2. DRIVE CYCLE A (AFTER RUNNING 20 MINUTES AT 80 KM/H (50 MPH), IDLE ENGINE FOR 1 MINUTE.
P0126 - P2103:
3. DRIVE CYCLE B (IDLE FOR 10 MINUTES)
NOTE: Before the diagnosis, drive the vehicle at 10 km/h (6 MPH) or more.
P0030 - P2103:
4. DRIVE CYCLE C (DRIVE ACCORDING TO THE FOLLOWING DRIVE PATTERN)
5. DRIVE CYCLE D
^ DRIFT DIAGNOSIS
1. Make sure that the engine coolant temperature at engine starting is less than 30 degrees C (86 degrees F).
2. Make sure that fuel of more than 10 2 (2.6 US gal, 2.2 Imp gal) remains and the battery voltage is more than 10.9 V.
3. Make sure that the engine coolant temperature rises for more than 10 degrees C (18 degrees F) from the level of engine starting and is also more than 75 degrees C (167 degrees F).
4. Idle the engine for more than 120 seconds in the condition of step 3.
^ STUCK DIAGNOSIS
1. Make sure that the battery voltage is more than 10.9 V.
2. Perform the clear memory mode.
P0181:
3. Drive the vehicle for the distance equal to fuel of 50 2 (13.2 US gal, 11 Imp gal).
NOTE:
- It is possible to drive intermittently.
- Do not disconnect the terminal of battery during diagnosis. (If disconnecting the terminal of battery, the data will be cleared.)
6. DRIVE CYCLE E
1. Make sure that the battery voltage is more than 10.9 V.
2. Perform the clear memory mode.
P0461:
3. Drive the vehicle for the distance equal to fuel of 30 2 (7.9 US gal, 6.6 Imp gal).
NOTE:
- It is possible to drive intermittently.
- Do not disconnect the terminal of battery during diagnosis. (If disconnecting the terminal of battery, the data will be cleared.)
7. DRIVE CYCLE F
1. Make sure that the engine coolant temperature at engine starting is less than 30 degrees C (86 degrees F).
2. Warm-up the engine until the engine coolant temperature is more than 95 degrees C (203 degrees F) from engine starting.
P0410 - P2443:
3. Idle the engine for more than 10 minutes in the condition of step 2).
NOTE: Do not disconnect the terminal of battery during diagnosis. (If disconnecting the terminal of battery, the data will be cleared.)
8. DRIVE CYCLE G
1. Disconnect the ground cable from battery. Wait for 10 seconds and then reconnect it.
2. Start the engine and idle it until engine coolant temperature becomes 80 degrees C (176 degrees F).
3. Turn the engine OFF, and wait until coolant temperature goes down to 40 degrees C (104 degrees F).
NOTE: Do not let the engine coolant temperature go down below 5 degrees C (41 degrees F).
4. Repeat the steps 2. and 3. again.
NOTE: Do not let the engine coolant temperature go down below than 5 degrees C (41 degrees F).
P0111:
5. Start and idle the engine.