Mechanical Specifications

Type		Automatic three speed with torque converter and integral differential
Torque Converter	Diameter	9.48 in
Cooling Method		Water Heat Exchanger and/or air to oil heat exchanger
Lubrication		Pump (internal - external gear - type)
Transmission Gear Ratios	First Gear	2.69 To 1 (: 1)
	Second Gear	1.55 To 1 (: 1)
	Third Gear	1.00 To 1 (: 1)
	Reverse Gear	2.10 To 1 (: 1)
Band Adjustment	Kickdown - Backed Off From	72 in lb 2 1/4 Turns
	Low - Reverse - Backed Off From	41 in lb 3 1/2 Turns
Clutch Pack Clearances	Front Clutch (Not Adjustable)	0.050 - 0.110 in
	Rear Clutch	0.028 - 0.043 in
End Play	Input Shaft	0.008 - 060 in
	Front Clutch Retainer	0.030 - 0.106 in
	Front Carrier	0.007 - 0.057 in
	Front Annulus Gear	0.0035 - 0.020 in
	Planet Pinion	0.006 - 0.023 in
	Reverse Drum	0.030 - 0.132 in
Oil Pump Clearances	Outer Gear To Pocket	0.0018 - 0.0056 in
	Outer Gear Side Clearance	0.0008 - 0.0018 in
	Inner Gear Side Clearance	0.0008 - 0.0018 in
Tapered Roller Bearing Settings	Differential Assembly	6 to 12 in lb Drag torque
	Output Hub	0 to 3 in lb Drag torque
	Transfer Shaft End Play	0.002 to 0.010 in
	Overall Drag At Output Hub	3 to 16 in lb Drag torque
Thrust Washers	Reaction Shaft Support (No. 1)	0.061 - 0.063 in
	Rear Clutch Retainer (No. 2)	0.061 - 0.063 in
	Output Shaft (No. 3) (Select)	0.077 - 0.080 in
	Output Shaft (No. 3) (Select)	0.085 - 0.087 in
	Output Shaft (No. 3) (Select)	0.092 - 0.095 in
	Front Annulus (No. 4)	0. 116 - 0.120 in
	Front Carrier (Nos. 5&6)	0.0948 - 0.050 in
	Sun Gear - Front (No. 7)	0.033 - 0.036 in
	Sun Gear - Rear (No. 8)	0.033 - 0.036 in
	Rear Carrier (Nos. 9&10)	0.0948 - 0.050 in
	Rev. Drum (No. 11)	0.061 - 0.063 in
Tightening Torque	Bell Housing Cover Bolts	105 Inch Pound-Force (in.lb)
	Cooler Hose To Rad. Conn	105 Inch Pound-Force (in.lb)
	Cooler Line Conn	250 Inch Pound-Force (in.lb)
	Diff. Bear. Ret. To Case Bolt	300 Inch Pound-Force (in.lb)
	Diff. Cover To Case Bolt	165 Inch Pound-Force (in.lb)
	Exten. Hous. To Case Bolt	250 Inch Pound-Force (in.lb)
	Flex Plate To Crankshaft Bolts	70 Foot Pound-Force (ft.lb)
	Flex Plate To Torque Conv. Bolts	50 Foot Pound-Force (ft.lb)
	Fluid Filter Screw	45 Inch Pound-Force (in.lb)
	Front Motor Mount Bolt	40 Foot Pound-Force (ft.lb)
	Governor Counterweight Screw	250 Inch Pound-Force (in.lb)
	Governor To Support Bolt	60 Inch Pound-Force (in.lb)
	Kickdown Band Adj. Lock Nut	35 Foot Pound-Force (ft.lb)
	Left Motor Mount Bolts	40 Foot Pound-Force (ft.lb)
	Lower Bell Housing Cover Screw	30 Foot Pound-Force (ft.lb)
	Manual Cable To Trans. Case Bolt	250 Inch Pound-Force (in.lb)
	Manual Control Lever Screw	105 Inch Pound-Force (in.lb)
	Oil Pan To Trans. Case Screw	165 Inch Pound-Force (in.lb)
	Output Gear Strap Bolts	17 Foot Pound-Force (ft.lb)
	Output Shaft Nut	200 Foot Pound-Force (ft.lb)
	Park/Neutral Switch	25 Foot Pound-Force (ft.lb)
	Pressure Check Plug	45 Inch Pound-Force (in.lb)
	Pump To Case Bolts	275 Inch Pound-Force (in.lb)
	Reaction Shaft Assembly Bolt	250 Inch Pound-Force (in.lb)
	Rear Cover To Case Screw	165 Inch Pound-Force (in.lb)
	Reverse Band Adj. Lock Nut	125 Inch Pound-Force (in.lb)
	Reverse Band Shaft Plug	60 Inch Pound-Force (in.lb)
	Ring Gear Screw	70 Foot Pound-Force (ft.lb)
	Speedo. To Ext. Hous. Screw	60 Inch Pound-Force (in.lb)
	Sprag Ret. To Transfer Case Bolt	250 Inch Pound-Force (in.lb)
	Starter To Trans. Bell Bolts	40 Foot Pound-Force (ft.lb)
	Stirrup Strap Ret. Bolts	200 Inch Pound-Force (in.lb)
	Throttle Cable To Trans. Case Bolt	105 Inch Pound-Force (in.lb)
	Throttle Lever To Trans. Shaft Bolts	105 Inch Pound-Force (in.lb)
	Trans. To Cyl. Block Bolt	70 Foot Pound-Force (ft.lb)
	Transfer Shaft Nut	200 Foot Pound-Force (ft.lb)
	Transfer Gear Strap Bolts	17 Foot Pound-Force (ft.lb)
	Valve Body Assy. To Case Bolts	105 Inch Pound-Force (in.lb)
	Valve Body Screw	45 Inch Pound-Force (in.lb)