Manual Transaxle Removal/Installation
MANUAL TRANSAXLE REMOVAL/INSTALLATION [C66M-R]
1. Remove the battery cover. Removal and Replacement
2. Disconnect the negative battery cable. Removal and Replacement
3. Remove the aerodynamic under cover No.2 and the splash shield as a single unit. Aerodynamic Under Cover No. 2 Removal/Installation Splash Shield Removal/Installation
4. Drain the manual transaxle oil. Manual Transaxle Oil Replacement [C66M-R]
5. Disconnect and/or remove the following parts in the engine compartment.
a. Remove the battery component. (ex: battery, battery tray and PCM component) Removal and Replacement
b. Remove the air cleaner component. (ex: air cleaner, air hose) Service and Repair
c. Disconnect the control cable from MTX. Service and Repair
d. Disconnect the connectors and GND wiring harness from the MTX.
e. Remove the brackets from MTX.
6. Disconnect and/or remove the following parts related to the suspension and axle.
a. Remove the front tires. Procedures
b. Disconnect the clip securing the brake hose from the shock absorber. Brake Hose (Front) Removal/Installation
c. Disconnect the ABS wheel-speed sensors from the steering knuckles. Antilock Braking System (ABS)
d. Disconnect the tie-rod end ball joints from the steering knuckles. Service and Repair
e. Disconnect the stabilizer control links (upper side) from the shock absorbers. Front Suspension - Stabilizer Removal/Installation
f. Disconnect the front lower arms from the steering knuckles. Service and Repair
g. Disconnect the drive shaft (LH) from the MTX. Drive Shaft Removal/Installation
h. Disconnect the drive shaft (RH) from the joint shaft. Drive Shaft Removal/Installation
i. Remove the joint shaft. Joint Shaft Removal/Installation
7. Disconnect and/or remove the following parts from the underside of the vehicle.
a. Remove the hanger rubber from the exhaust manifold.
b. Disconnect the clutch release cylinder from MTX. Service and Repair
c. Remove the starter. Removal and Replacement
8. Install the SST using the following procedure.
CAUTION:
- Refer to the SST instruction manual for the basic handing procedure.
a. Remove the windshield wiper arm and blade. Windshield Wiper Arm And Blade Removal/Installation
b. Remove the front fender molding. Cowl Grille Removal/Installation
c. Remove the cowl grille. Cowl Grille Removal/Installation
d. Remove the cowl panel. Cowl Panel Removal/Installation
e. Protect the windshield using tape.
f. Replace the hood stay to the position shown in the figure.
NOTE:
- The hood opening angle is increased by placing the hood stay to the position shown in the figure. A space for installing the SST can be secured by increasing the hood opening angle.
i. Disconnect the washer tank and set it aside.
ii. Tilt the hood stay in the direction of the arrow shown in the figure.
iii. Pull out the hood stay in the direction of the arrow shown in the figure.
iv. Rotate the hood stay at the pivot fulcrum shown in the figure.
v. Remove the hood stay.
vi. Install the hood stay as shown in the figure.
CAUTION:
- If the hood stay is not hooked to the hood hole, the hood may fall down. Lightly shake the hood to verify that the hood stay is hooked securely.
g. To enable to install the SST, disconnect the clip shown in the figure and set the wiring harness aside.
h. Install the SST using part number 99794 1025 or an M10x1.25, length 25 mm {0.98 in} bolt as shown in the figure.
Engine front side
Tightening torque
- 38-51 Nm {3.9-5.2 kgf-m, 29-37 ft-lbf}
Engine rear side
Tightening torque
- 38-51 Nm {3.9-5.2 kgf-m, 29-37 ft-lbf}
i. Align the bolt of the shock absorber (RH) shown in the figure with the rear shaft hole for the right side of the SST.
j. Align the bolt of the shock absorber (LH) shown in the figure with the rear shaft hole for the left side of the SST.
k. Install one front foot No.2 to each of the left and right front shafts of the SST, and then align the holes of the SST front shafts with the bolt on the left and right side of each front side frame.
l. Install the SST (49 L017 5A0) to the SST (49 C017 5A0) as shown in the figure.
m. Install the SST (49 L017 5A0) to the SST (49 UN30 3050) with the hook of the SST (49 L017 5A0) facing outward.
CAUTION:
- Install the SST (49 L017 5A0) so that it does not interfere with parts such as the fuel pipe. If the SST (49 L017 5A0) interferes, parts such as the fuel pipe could be damaged.
n. Adjust the height of the left and right side bars so that they are leveled, then tighten each part of the SST.
o. Apply tension to the chain to secure the engine.
9. Remove in the order indicated in the table.
10. Install in the reverse order of removal.
11. Add the specified amount of specified transaxle oil. Manual Transaxle Oil Replacement [C66M-R]
12. If the manual transaxle is overhauled, perform the "INSPECTION AFTER MANUAL TRANSAXLE OVERHAUL". Inspection After Manual Transaxle Overhaul [C66M-R]
Manual Transaxle Installation Note
WARNING:
- Install the transaxle carefully, holding it steady. If the transaxle falls it could be damaged or cause injury.
1. Set the transaxle on a jack and lift into place.
2. Install the transaxle mounting bolts.
Tightening torque
- 38-51 Nm {3.9-5.2 kgf-m, 29-37 ft-lbf}
3. Adjust the SST (49 C017 5A0) so that the engine is located at the specified position.
No.1 Engine Mount and No.4 Engine Mount Installation Note
1. Install the No.4 engine mount bracket to the transaxle case.
2. Install the No.1 engine mount bracket to the transaxle case.
Tightening torque
- 94-112 Nm {9.6-11 kgf-m, 70-82 ft-lbf}
3. Temporarily tighten the bolts as shown in the figure.
4. Place the No.4 engine mount rubber with the body stud bolts passing through the holes and tighten the bolt in the figure.
5. Fully tighten the bolts in the order shown in the figure and install the No.1 engine mount rubber.
Tightening torque
- 73-90 Nm {7.5-9.1 kgf-m, 54-66 ft-lbf}
6. Place the battery bracket on the No.4 Engine mount rubber with the body stud bolts passing through the holes and tighten bolts and nuts.
7. Remove the SST (49 C017 5A0).