After Repair Procedure

AFTER REPAIR PROCEDURE

Caution
- After repairing a malfunction, perform this procedure to verify that the malfunction has been corrected.
- When this procedure is carried out, be sure to drive the vehicle at lawful speed and pay attention to the other vehicles.

1. Connect the SSTs (NGS tester) to the DLC-2.
2. Turn the ignition key to ON (engine off).
3. Select the clear code function and clear the DTC.
4. Perform the following DTC inspections to ensure that the DTC has been resolved:
- For P0705
i. Start the engine.
ii. Drive the vehicle in each range (P. R, N, D, 2, and 1) for 10 seconds or more.
iii. Go to Step 5.
- For P0706
i. Start the engine.
ii. Access VS PID using the SSTs (NGS tester).
iii. Drive the vehicle in each range (D, 2, and 1) under the following conditions for 25 seconds or more while monitoring PIDs.
- VS PID: 60 km/h (37 mph) or above
iv. Go to Step 5.
- For P0715
i. Start the engine.
ii. Access VS PID using the SSTs (NGS tester).
iii. Drive the vehicle under the following conditions for 50 seconds or more.
- VS PID: 20 km/h (12.4 mph)
- D range position
- 1GR
iv. Go to Step 5.
- For P0720
i. Start the engine.
ii. Access VS PID using the SSTs (NGS tester).
iii. Drive the vehicle under the following conditions for 85 seconds or more while monitoring PID.
- VS PID: 60 km/h (37 mph) or above
- D range position
- 3GR
iv. Go to Step 5.
- For P0725
i. Start the engine.
ii. Access VS PID using the SSTs (NGS tester).
iii. Drive the vehicle under the following condition for 10 seconds or more while monitoring PID.
- VS PID: 60 km/h (37 mph) or above
iv. Go to Step 5.
- For P0741, P0742
i. Start the engine.
ii. Warm up the engine and transmission.
iii. Access ECT, RPM, and VS PIDs using the SSTs (NGS tester).
iv. Drive the vehicle under the following conditions for 24 seconds or more while monitoring PIDs
- VS PID: Within 5 km/h (3.1 mph) - 100 km/h (62 mph)
- ECT PID: 60° C (140° F) or above
- RPM PID: 600 rpm or above
- 3GR and 4GR
- D range position
- TCC operation
v. Go to Step 5.
- For P0751, P0752, P0756, P0757
i. Start the engine.
ii. Warm up the engine and transmission.
iii. Access ECT, RPM, and VS PIDs using the SSTs (NGS tester).
iv. Drive the vehicle and make sure that the gears shift smoothly from 1GR to 4GR under the following conditions.
- ECT PID: 60° C (140° F) or above
- RPM PID: 600 rpm or above
- VS PID: 5 km/h (3.1 mph) or above
v. Go to Step 5.
- For P1740, P1742, P1751, P1752, P1756, P1757
i. Start the engine.
ii. Warm up the engine and transmission.
iii. Drive the vehicle in D range and make sure that the gears shift smoothly from 1GR to 4GR and TCC is operated.
iv. Go to Step 5.
- For P1771, P1772
i. Start the engine for 2 seconds or more.
ii. Go to Step 6.
5. Gradually slow down and stop the vehicle.
6. Make sure that the repaired DTC does not recur.