Front

Special Tool(s):

SPECIAL TOOL(S)

REMOVAL

WARNING:
^ ALWAYS WEAR SAFETY GLASSES WHEN REPAIRING A AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) VEHICLE AND WHEN HANDLING AN AIRBAG MODULE. THIS WILL REDUCE THE RISK OF INJURY IN THE EVENT OF AN ACCIDENTAL DEPLOYMENT.
^ AFTER DEPLOYMENT, THE AIR BAG SURFACE CAN CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTERWARDS.
^ NEVER PROBE THE CONNECTORS ON THE AIR BAG MODULE. DOING SO CAN RESULT IN AIR BAG DEPLOYMENT, WHICH CAN RESULT IN PERSONAL INJURY.

NOTE:
^ If a side air bag deployment took place the seatback pad, trim cover, and side air bag module must be replaced. The seatback frame should be replaced if necessary.
^ The left side is shown, the right side is similar.

All seats
1. Prepare the vehicle for front seat backrest removal.
1 Disconnect the battery ground cable and wait at least one minute.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY FRONT OR SIDE AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) COMPONENTS AND BEFORE SERVICING, REPLACING, ADJUSTING OR STRIKING COMPONENTS NEAR THE FRONT OR SIDE AIR BAG SENSORS, SUCH AS DOORS, INSTRUMENT PANEL, CONSOLE, DOOR LATCHES, STRIKERS, SEATS AND HOOD LATCHES.

PLEASE REFER TO THE APPROPRIATE COMPONENT OR SYSTEM TO DETERMINE LOCATION OF THE FRONT AIR BAG SENSORS.

THE SIDE AIR BAG SENSORS ARE LOCATED AT OR NEAR THE BASE OF THE B-PILLAR.

TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT AT LEAST ONE MINUTE. BE SURE TO DISCONNECT AUXILIARY BATTERIES AND POWER SUPPLIES (IF EQUIPPED).

2 Deactivate the supplemental restraint system (SRS).

WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, READ AND FOLLOW ALL WARNINGS, NOTES, AND INSTRUCTIONS IN THE SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEACTIVATION AND REACTIVATION PROCEDURE.

3 Remove the affected seat.

WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, READ AND FOLLOW ALL WARNINGS, CAUTIONS, NOTES, AND INSTRUCTIONS IN THE SEAT REMOVAL AND INSTALLATION PROCEDURE.







2. Remove the seat backrest trim panel.
1 Pull and release the pin-type retainers at the bottom of the seat backrest trim panel.
2 While holding the seat backrest trim panel at the bottom, push in on the left side of the panel at the lip of the map pocket and slide it to the right to disengage the J-hook. Repeat this process for the right side J-hook but slide the panel to the left to disengage the hook.
3 While pushing in at the top of the seat backrest trim panel, slide it down to disengage the top J-hooks.
4 Remove the seat backrest trim panel and inspect the J-hooks and pin-type retainers for damage.

WARNING: FRONT SEAT BACK TRIM COVERS INSTALLED ON SEATS EQUIPPED WITH SIDE AIR BAGS CANNOT BE REPAIRED, THEY ARE TO BE REPLACED (CLEANING IS PERMISSIBLE).

CAUTION:
^ When removing the seat backrest trim panel, be careful not to damage the J-hooks. If the seat backrest trim panel J-hooks are damaged, install a new seat backrest trim panel.
^ When removing the seat backrest trim panel, be careful not to damage the pin-type retainers. Pulling towards you, use a smooth, controlled force to release the pin-type retainers.

Seats with manual lumbar







3. Remove the retaining hook.







4. Align the end of the adjusting cable in the slot.







5. Release the adjusting cable.

All seats







6. Disconnect the electrical connectors.







7. Disconnect the electrical connector.
8. Remove the front cushion side shield trim panel.







9. Remove the two front seat backrest bolts on each side. Remove the front seat backrest.

INSTALLATION

WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, READ AND FOLLOW ALL WARNINGS AND NOTES AT THE BEGINNING OF THE REMOVAL PROCEDURE.

All seats







1. Position the front seat backrest and install two bolts on each side.
2. Install the front cushion side shield trim panel.







3. Connect the electrical connector.







4. Connect the electrical connectors.

Seats with manual lumbar







5. Install the retaining hook.







6. Align the end of the adjusting cable in the slot.







7. Install the adjusting cable.







8. Install the seat backrest trim panel.
1 Angle the top of the seat backrest trim panel inward and up to engage the upper J-hooks to the seat backrest frame.
2 While holding the seat backrest trim panel up, align the pin-type retainers at the bottom of the seat backrest trim panel and install them into the seat backrest frame.
3 With the palm of your hand, install the J-clips by pushing down on the seat backrest trim panel and towards the center of the seat.
^ Check the retention of the seat backrest trim panel by lightly pulling on the bottom, sides, and top where the retainers are located.

CAUTION: Inspect the seat backrest trim panel J-hooks for damage. If damaged, install a new seat backrest trim panel.

NOTE: If re-installing the original seat backrest trim panel, install new pin-type retainers.

9. Restore the vehicle to operating condition.
1 Install the affected seat.

WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, READ AND FOLLOW ALL WARNINGS, NOTES, AND INSTRUCTIONS IN THE SEAT REMOVAL AND INSTALLATION PROCEDURE.

2 Reactivate the supplemental restraint system (SRS).

WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, READ AND FOLLOW ALL WARNINGS, CAUTIONS, NOTES, AND INSTRUCTIONS IN THE SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEACTIVATION AND REACTIVATION PROCEDURE.

3 With all the restraint system diagnostic tools removed, prove out the supplemental restraint system (SRS).

WARNING: THE RESTRAINT SYSTEM DIAGNOSTIC TOOL IS FOR RESTRAINT SYSTEM SERVICE ONLY. REMOVE FROM THE VEHICLE PRIOR TO ROAD USE. FAILURE TO REMOVE COULD RESULT IN INJURY AND POSSIBLE VIOLATION OF VEHICLE SAFETY STANDARDS.

4 Check the active restraint system for correct operation.