Installation

SUSPENSION: REAR SUSPENSION MEMBER: INSTALLATION

1. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING CUSHION (for Rear Side)

(a) Apply soapy water around the outside of a new rear suspension member body mounting cushion.

(b) Position the body mounting cushion as shown in the illustration, and install it to the rear suspension member.

(c) Using SST, press in the body mounting cushion.

SST : 09316-12010

SST : 09570-24011

SST : 09950-40011

09951-04020

09952-04010

09953-04030

09954-04020

09955-04051

09957-04010

09958-04011

SST : 09950-60020

09951-00910

NOTICE:
Do not apply excessive force to the inner cylinder of the body mounting cushion.

3. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING CUSHION RH (for Front Side)

HINT
Use the same procedures described for the LH side.

4. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION Installation

5. INSTALL REAR NO. 2 DIFFERENTIAL MOUNT CUSHION Installation

6. TEMPORARILY INSTALL REAR UPPER NO. 2 CONTROL ARM ASSEMBLY LH

(a) Temporarily install the control arm with the bolt, nut and washer to the suspension member.

7. TEMPORARILY INSTALL REAR UPPER NO. 2 CONTROL ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

8. TEMPORARILY INSTALL REAR UPPER NO. 1 CONTROL ARM ASSEMBLY LH

(a) Temporarily install the control arm with the bolt, nut and washer to the suspension member.

9. TEMPORARILY INSTALL REAR UPPER NO. 1 CONTROL ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

10. TEMPORARILY INSTALL TOE CONTROL LINK SUB-ASSEMBLY LH

(a) Insert the toe adjust cam from the front of the vehicle and connect the toe control link. Then temporarily install the No. 2 suspension toe adjust plate with the nut.

NOTICE:
Align the matchmarks of the No. 2 suspension toe adjust plate and suspension member.

11. TEMPORARILY INSTALL TOE CONTROL LINK SUB-ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

12. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

(a) Temporarily install the No. 1 suspension arm with the bolt and nut to the suspension member.

13. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

14. INSTALL REAR SUSPENSION MEMBER DAMPER Installation

15. INSTALL REAR ACTIVE STABILIZER CONTROL ACTUATOR ASSEMBLY (w/ Active Stabilizer) Installation

16. INSTALL REAR STABILIZER BAR (w/o Active Stabilizer) Installation

17. INSTALL ELECTRIC PARKING BRAKE ACTUATOR Installation

18. INSTALL REAR STABILIZER LINK ASSEMBLY LH

(a) Install the stabilizer link with the nut to the stabilizer bar.

Torque : 89 Nm (908 kgf-cm, 66 ft-lbf)

19. INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

20. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

(a) Support the rear suspension member with an engine lift and attachments.

CAUTION:
* As the rear suspension member is very heavy, securely support it with the engine lift with attachments.
* Perform this procedure with several people supporting the rear suspension member so that it does not tilt or fall.
(b) Slowly raise the engine lift so that the rear suspension member is at its installation position.

(c) w/ Active Stabilizer:

(1) Attach the 3 claws to install the wire harness grommet of the active stabilizer control actuator.

HINT
Install the grommet so that the arrow of the grommet is facing the top of the vehicle.

(d) Install the 2 rear suspension member stopper lowers, and the 2 differential support member stopper lowers with the 4 bolts.

Torque : 117 Nm (1193 kgf-cm, 86 ft-lbf)

21. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DRIVE SHAFT Installation

22. INSTALL REAR SUSPENSION MEMBER BRACE LH Installation

23. INSTALL REAR SUSPENSION MEMBER BRACE RH

HINT
Use the same procedures described for the LH side.

24. INSTALL REAR AXLE ASSEMBLY LH Installation

25. INSTALL REAR AXLE ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

26. INSTALL REAR AXLE SHAFT NUT LH Installation

27. INSTALL REAR AXLE SHAFT NUT RH

HINT
Use the same procedures described for the LH side.

28. TEMPORARILY INSTALL REAR UPPER NO. 1 CONTROL ARM ASSEMBLY LH Installation

29. TEMPORARILY INSTALL REAR UPPER NO. 1 CONTROL ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

30. TIGHTEN REAR UPPER NO. 1 CONTROL ARM ASSEMBLY LH Installation

31. TIGHTEN REAR UPPER NO. 1 CONTROL ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

32. TEMPORARILY INSTALL REAR UPPER NO. 2 CONTROL ARM ASSEMBLY LH Installation

33. TEMPORARILY INSTALL REAR UPPER NO. 2 CONTROL ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

34. TIGHTEN REAR UPPER NO. 2 CONTROL ARM ASSEMBLY LH Installation

35. TIGHTEN REAR UPPER NO. 2 CONTROL ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

36. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH Installation

37. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

38. TEMPORARILY INSTALL TOE CONTROL LINK SUB-ASSEMBLY LH Installation

39. TEMPORARILY INSTALL TOE CONTROL LINK SUB-ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

40. TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY LH Installation

41. TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

42. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH Installation

43. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

44. TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH Installation

45. TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

46. TEMPORARILY INSTALL PNEUMATIC CYLINDER REAR WITH SHOCK ABSORBER ASSEMBLY LH Installation

47. TEMPORARILY INSTALL PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER RH

HINT
Use the same procedures described for the LH side.

48. INSTALL REAR STABILIZER LINK ASSEMBLY LH

(a) Install the stabilizer link with the nut to the No. 2 suspension arm.

Torque : 26 Nm (265 kgf-cm, 19 ft-lbf)

49. INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

50. INSTALL LOAD SENSING VALVE SENSOR BRACKET Installation

51. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH Installation

52. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

53. INSTALL SKID CONTROL SENSOR WIRE Installation

54. APPLY HIGH TEMPERATURE GREASE Reassembly

55. INSTALL PARKING BRAKE CABLE LH Installation

56. INSTALL PARKING BRAKE CABLE RH Installation

57. INSTALL PARKING BRAKE SHOE LEVER LH Reassembly

58. INSTALL PARKING BRAKE SHOE LEVER RH

HINT
Use the same procedures described for the LH side.

59. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH Reassembly

60. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY RH Installation

61. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH Reassembly

62. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY RH Installation

63. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET LH Reassembly

64. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET RH Installation

65. INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING Reassembly

66. INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING Reassembly

67. CHECK PARKING BRAKE INSTALLATION Reassembly

68. INSPECT REAR AXLE HUB BEARING LOOSENESS Rear Axle Hub

69. INSPECT REAR AXLE HUB RUNOUT Rear Axle Hub

70. INSTALL REAR DISC Installation

71. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH Installation

72. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

73. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

74. INSTALL ELECTRIC PARKING BRAKE ACTUATOR CAP Installation

75. INSTALL FLOOR NO. 1 UNDER COVER Installation

76. INSTALL REAR WHEEL HOUSE LINER LH Installation

77. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY Installation

78. TIGHTEN NO. 1 CENTER SUPPORT BEARING ASSEMBLY Installation

79. INSPECT AND ADJUST NO. 2 AND NO. 3 JOINT ANGLE Installation

80. INSTALL PROPELLER SHAFT HEAT INSULATOR Installation

81. INSTALL FRONT FLOOR NO. 1 HEAT INSULATOR Installation

82. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY Installation

83. INSTALL EXHAUST PIPE DAMPER Installation

84. INSTALL TAILPIPE RH Installation

85. INSTALL TAILPIPE LH Installation

86. CONNECT HEATED OXYGEN SENSOR (for Bank 1 Sensor 2) Installation

87. INSTALL FRONT EXHAUST PIPE ASSEMBLY Installation

88. INSTALL EXHAUST GAS TEMPERATURE SENSOR Installation

89. INSTALL EXHAUST PIPE AIR HOSE Installation

90. INSTALL NO. 2 HEATED OXYGEN SENSOR (for Bank 2 Sensor 2) Installation

91. INSTALL FRONT CENTER FLOOR BRACE Installation

92. INSTALL FRONT CENTER FLOOR COVER Installation

93. INSTALL FRONT FLOOR COVER RH Installation

94. INSTALL FRONT FLOOR COVER LH Installation

95. INSTALL REAR FLOOR SIDE MEMBER COVER RH Installation

96. INSTALL REAR FLOOR SIDE MEMBER COVER LH Installation

97. INSTALL NO. 5 ROCKER PANEL MOULDING PROTECTOR Installation

98. INSTALL NO. 6 ROCKER PANEL MOULDING PROTECTOR Installation

99. INSTALL NO. 1 DIFFERENTIAL SUPPORT PROTECTOR Installation

100. INSTALL NO. 2 DIFFERENTIAL SUPPORT PROTECTOR Installation

101. INSTALL REAR ACTIVE STABILIZER CONTROL ECU ASSEMBLY (w/ Active Stabilizer) Installation

102. CONNECT REAR ACTIVE STABILIZER CONTROL ACTUATOR CONNECTOR (w/ Active Stabilizer) Installation

103. INSTALL SEAT VIBRATOR MODULE ASSEMBLY (for Ottoman) Installation

104. INSTALL BATTERY CARRIER Installation

105. INSTALL BATTERY Installation

106. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH Installation

107. INSTALL REAR FLOOR FINISH PLATE Installation

108. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER Installation

109. INSTALL NO. 1 COOLER COVER (w/ Rear Air Conditioning System) Installation

110. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY Installation

111. INSTALL DECK TRIM SIDE BOARD RH Installation

112. INSTALL ROPE HOOK ASSEMBLY Installation

113. INSTALL ROPE HOOK Installation

114. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected ( Repair Instruction - Initialization).

115. INSTALL BATTERY SERVICE HOLE COVER LH Installation

116. INSTALL SPARE TIRE

117. INSTALL TOOL BOX (w/o Spare Tire) Installation

118. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

119. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

120. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY Installation

121. STABILIZE SUSPENSION Installation

122. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH Installation

123. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

124. TIGHTEN PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH Installation

125. TIGHTEN PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY RH

HINT
Use the same procedures described for the LH side.

126. INSPECT REAR UPPER NO. 1 CONTROL ARM BALL JOINT LOOSENESS On-Vehicle Inspection

127. INSPECT REAR UPPER NO. 2 CONTROL ARM BALL JOINT LOOSENESS On-Vehicle Inspection

128. INSPECT REAR NO. 1 SUSPENSION ARM BALL JOINT LOOSENESS On-Vehicle Inspection

129. INSPECT TOE CONTROL LINK BALL JOINT LOOSENESS On-Vehicle Inspection

130. ADJUST PARKING BRAKE SHOE CLEARANCE Installation

131. INSTALL REAR WHEEL

Torque : 140 Nm (1428 kgf-cm, 103 ft-lbf)

132. CHECK SUSPENSION CONTROL SYSTEM

(a) Check the suspension control system Adjustments.

133. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

(a) Inspect and adjust the rear wheel alignment Rear Wheel Alignment.

134. CHECK SPEED SENSOR SIGNAL

(a) Check the speed sensor signal Test Mode Procedure.

135. ADJUST HEADLIGHT ASSEMBLY

(a) for LED headlight:

Adjust the headlight (for LED Headlight).

(b) for HID headlight:

Adjust the headlight (for HID Headlight).

136. ADJUST OBJECT RECOGNITION CAMERA

(a) Adjust the object recognition camera Adjustments.

137. INSPECT FOR EXHAUST GAS LEAK Installation