Operation CHARM: Car repair manuals for everyone.
Hosted by mcallihan.com
Home >> Lexus >> 2010 >> IS F V8-5.0L (2UR-GSE) >> Repair and Diagnosis >> Body and Frame >> Roof and Associated Components >> Sunroof / Moonroof >> Service and Repair >> Removal and Replacement >> Installation

Installation





SLIDING ROOF / CONVERTIBLE: SLIDING ROOF HOUSING: INSTALLATION

1. INSTALL SLIDING ROOF WEATHERSTRIP

(a) Install the sliding roof weatherstrip as follows:





(1) Position the joint of the weatherstrip at the rear center.

(2) Align the marks on the weatherstrip with the middle marks at the corners of the plastic on the edge of the sliding roof panel and install the weatherstrip. Make sure that the marks on the weatherstrip are positioned within the area indicated by the marks at the corners of the plastic on the edge of the sliding roof panel.

(3) Install the lip of the weatherstrip firmly.

2. INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY

(a) Install the sliding roof housing sub-assembly with the 6 bolts and 8 nuts.





Nut - Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)

Bolt - Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)

(b) Connect the 4 sliding roof drain hoses.





NOTICE:
The clip must face toward the outside of the vehicle and also be above the lower surface of the sliding roof housing when installing the drain hoses.

3. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

(a) Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.





(b) Perform a level check.





(1) Check the difference in level for "a" between the roof panel and the upper surface of the weather strip when the sliding roof glass is fully closed.

Standard:





HINT
"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

(c) Perform a gap check.





(1) Check the gap between the roof panel and roof glass.

NOTICE:
The gap must be even all around.

(d) After adjusting the sliding roof glass, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.





Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)

4. CHECK FOR WATER LEAK

(a) After adjusting the sliding roof glass sub-assembly, check for water leaks.

(b) If there are any leaks, readjust the sliding roof glass sub-assembly.

5. INSTALL SLIDING ROOF SIDE GARNISH LH

(a) Engage the 5 claws and install the sliding roof side garnish LH.





6. INSTALL SLIDING ROOF SIDE GARNISH RH

HINT
Use the same procedure for the RH side and LH side.

7. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH Installation

8. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT
Use the same procedure for the RH side and LH side.

9. INSTALL ROOF HEADLINING ASSEMBLY Installation

10. INSTALL VISOR HOLDER Installation

11. INSTALL VISOR ASSEMBLY LH Installation

12. INSTALL VISOR ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

13. INSTALL VISOR BRACKET COVER Installation

14. INSTALL ASSIST GRIP SUB-ASSEMBLY Installation

15. INSTALL COAT HOOK Installation

16. INSTALL SPOT LIGHT ASSEMBLY Installation

17. INSTALL MAP LIGHT ASSEMBLY Installation

18. INSTALL RAIN SENSOR TAPE Installation

19. INSTALL RAIN SENSOR Installation

20. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER Installation

21. INSTALL ROOF SIDE INNER GARNISH LH Installation

22. INSTALL ROOF SIDE INNER GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

23. INSTALL REAR SEAT SIDE GARNISH LH Installation

24. INSTALL REAR SEAT SIDE GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

25. INSTALL CENTER PILLAR GARNISH LH Installation

26. INSTALL LOWER CENTER PILLAR GARNISH LH Installation

27. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH Installation

28. INSTALL LAP BELT OUTER ANCHOR COVER LH Installation

29. INSTALL CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

30. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH Installation

31. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

32. INSTALL FRONT SEAT BELT ANCHOR COVER SUB-ASSEMBLY Installation

33. INSTALL REAR DOOR SCUFF PLATE LH Installation

34. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

35. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY Installation

36. CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY Installation

37. ADJUST SHIFT LEVER POSITION Adjustments

38. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR Installation

39. INSTALL FRONT EXHAUST PIPE ASSEMBLY Installation

40. CONNECT HEATED OXYGEN SENSOR Installation

41. INSTALL FRONT CENTER FLOOR BRACE Installation

42. INSTALL REAR NO. 1 FLOOR PANEL BRACE Installation

43. INSTALL TAIL EXHAUST PIPE ASSEMBLY Installation

44. INSTALL NO. 2 FLOOR UNDER COVER Installation

45. INSTALL NO. 1 FLOOR UNDER COVER Installation

46. INSTALL INSTRUMENT PANEL STAY Installation

47. INSTALL INSTRUMENT PANEL CLIP Installation

48. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY Installation

49. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY Installation

50. INSTALL NO. 1 CONSOLE BOX DUCT Installation

51. INSTALL NO. 2 CONSOLE BOX DUCT Installation

52. INSTALL FRONT STEREO COMPONENT SPEAKER ASSEMBLY (w/ Front Center Speaker) Installation

53. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY Installation

54. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY Installation

55. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY Installation

56. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY Installation

57. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY Installation

58. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Installation

59. INSTALL SIDE INSTRUMENT PANEL RH Installation

60. INSTALL COMBINATION METER ASSEMBLY Installation

61. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Installation

62. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation

63. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY Installation

64. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Installation

65. INSTALL SIDE INSTRUMENT PANEL LH Installation

66. INSTALL FRONT PILLAR GARNISH LH Installation

67. INSTALL FRONT PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

68. INSTALL FRONT DOOR OPENING TRIM COVER LH Installation

69. INSTALL FRONT DOOR OPENING TRIM COVER RH

HINT
Use the same procedure for the RH side and the LH side.

70. INSTALL FRONT DOOR SCUFF PLATE LH Installation

71. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

72. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY Installation

73. INSTALL STEERING COLUMN COVER Installation

74. ADJUST SPIRAL CABLE SUB-ASSEMBLY Installation

75. INSTALL STEERING WHEEL ASSEMBLY Installation

76. INSTALL STEERING PAD Installation

77. INSTALL LOWER NO. 3 STEERING WHEEL COVER Installation

78. INSTALL LOWER NO. 2 STEERING WHEEL COVER Installation

79. INSTALL INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Navigation System) Installation

80. INSTALL MULTI-DISPLAY WITH RADIO RECEIVER ASSEMBLY (w/ Navigation System) Installation

81. INSTALL CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL Installation

82. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY Installation

83. INSTALL CONSOLE BOX Installation

84. INSTALL CONSOLE BOX REGISTER ASSEMBLY Installation

85. INSTALL REAR ASH RECEPTACLE ASSEMBLY Installation

86. INSTALL FRONT ASH RECEPTACLE ASSEMBLY Installation

87. INSTALL CONSOLE PANEL SUB-ASSEMBLY Installation

88. INSTALL UPPER NO. 2 CONSOLE PANEL GARNISH Installation

89. INSTALL UPPER NO. 1 CONSOLE PANEL GARNISH Installation

90. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY Installation

91. INSTALL FRONT SEAT ASSEMBLY LH Installation

92. INSTALL REAR INNER SEAT TRACK BRACKET COVER LH Installation

93. INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH Installation

94. INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH Installation

95. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH Installation

96. INSTALL FRONT SEAT ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

97. INSTALL REAR INNER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and the LH side.

98. INSTALL REAR OUTER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and the LH side.

99. INSTALL FRONT INNER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and the LH side.

100. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and the LH side.

101. INSTALL FRONT SEAT HEADREST ASSEMBLY

102. INSTALL REAR SEATBACK ASSEMBLY Installation

103. INSTALL REAR SEAT HEADREST ASSEMBLY LH

104. INSTALL REAR SEAT HEADREST ASSEMBLY RH

105. INSTALL REAR SEAT CUSHION ASSEMBLY Installation

106. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Testing and Inspection.

107. RESET SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

Customize Parameters

108. CHECK SLIDING ROOF SYSTEM

Operation Check

109. INSPECT STEERING PAD Installation

110. INSPECT SRS WARNING LIGHT

Diagnosis System

111. INSPECT FRONT SEAT ASSEMBLY Installation

112. INSPECT SHIFT LEVER POSITION Initial Inspection and Diagnostic Overview

113. INSPECT FOR EXHAUST GAS LEAK

If exhaust gas is leaking, tighten the related parts to stop the leak. Replace damaged parts as necessary.
pro multis · About Operation CHARM