Removal
The content of this article/image reflects the changes identified in Land Rover TSB - LTB00143
Engine
Service Repair No - 12.41.01.99
Removal
1. Secure the hood in the service position.
2. Disconnect the battery ground cable.
3. Remove the battery cover.
^ Release the 2 mounting clips.
4. Disconnect the battery positive cable.
5. Remove 2 bolts securing the battery clamp and remove the clamp.
6. Remove the battery.
7. Remove the engine compartment upper heat shield.
^ Remove the 2 screws.
^ Release the 2 mounting clips.
8. Remove the battery compartment side wall.
^ Release the battery positive cable and grommet.
^ Release the 4 clips.
9. Release the cassette.
^ Release the 2 clips.
10. Disconnect the engine wiring harness.
^ Release and disconnect the 2 electrical connectors.
11. Remove the RH air cleaner assembly.
WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands.
12. Raise and support the vehicle.
13. Remove the fender splash shields.
14. Release the dynamic response pump and tie aside.
^ Remove the 3 bolts.
15. Remove the generator.
16. Remove the dynamic response and generator mounting brackets
^ Remove the 8 bolts.
17. Drain the cooling system.
18. Drain the engine oil.
19. Remove the exhaust system.
20. Remove the oil cooler pipe support bracket.
^ Remove the bolt.
CAUTION: Before disconnecting or removing the components, make sure the area around the joint faces and connections are clean. Plug open connections to prevent contamination.
21. Release the oil cooler.
^ Disconnect the oil cooler hoses.
^ Remove the 4 bolts.
22. Disconnect the engine oil cooler coolant hoses.
^ Position a container to collect the fluid spillage.
^ Clamp the relevant hoses, to minimize the coolant loss.
^ Release the 2 clips.
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
23. Release and tie aside the oil filter housing.
^ Remove the oil union bolt for access.
^ Remove the 3 bolts.
24. Remove the LH charge air cooler.
25. Remove the RH charge air cooler.
26. Release the power steering pump and tie aside
^ Remove the 3 bolts.
27. Release the A/C compressor and tie aside.
^ Remove the 3 bolts.
^ Disconnect the electrical connector.
28. Remove the A/C compressor mounting bracket.
^ Remove the 3 bolts.
29. Release the transmission cooler pipes.
^ Position a container to collect the fluid.
^ Remove the bolt.
^ Release the 2 clips.
^ Move the transmission pipes aside.
30. Release the flexplate.
^ Remove the grommet.
^ Rotate the crankshaft to access the retaining bolts.
^ Remove the 3 bolts.
WARNING: The spilling of fuel is unavoidable during this operation. Ensure that all necessary precautions are taken to prevent fire and explosion.
31. Remove the fuel temperature sensor.
^ Disconnect the electrical connector.
^ Position an absorbent cloth to collect fluid spillage.
CAUTION: Before disconnecting or removing components, ensure the area around the joint faces and connections are clean. Plug open connections to prevent contamination.
32. Remove the fuel rail pressure sensor.
^ Remove the 2 bolts.
^ Remove and discard the 2 0-ring seals.
33. Remove both camshaft position (CMP) sensors and brackets for access.
^ Remove the Torx screw.
^ Release the harness brackets.
NOTE: Naturally aspirated illustrated, mounting points are identical on the supercharged engine.
34. Install the engine lifting cradle.
35. Release the heat shield for access to the transmission bolts.
^ Remove the 2 bolts.
^ Move the shield aside.
36. Remove the transmission bolts.
^ Support the transmission.
^ Remove the 16 bolts.
37. Remove the upper suspension arm and brake line heat shields for access.
NOTE: Naturally aspirated graphic shown.
38. Remove the 2 engine mount nuts.
39. Release the engine from mounts and the transmission.
^ Install the lifting chains.
^ Raise the RH side of the engine by approximately 40 mm.
40. Disconnect the starter motor electrical connections.
^ Remove the nut.
41. Remove the starter motor.
^ Remove the starter motor retaining bolts.
CAUTION: Make sure the torque converter remains connected to the transmission.
CAUTION: Care must be taken to avoid damaging the steering rack and differential.
42. Remove the engine front mount bracket.
^ Remove 4 bolts securing the engine mount bracket to the cylinder block.
^ Disconnect the engine ground cable from the RH mounting bracket.
^ Carefully and progressively raise and remove the engine.
CAUTION: Make sure the torque converter remains connected to the transmission.
CAUTION: Care must be taken to avoid damaging the steering rack and differential.
43. Carefully and progressively raise and remove the engine.
44. Disconnect the lifting chains.
^ Remove the engine lifting cradle.
45. Position the engine.
^ Install the lifting chains.
^ Raise the engine.
^ Clean the component mating faces.
^ Clean the locating dowels.