P0345
P0340, P0345 CMP SENSOR
DTC Logic
DTC DETECTION LOGIC
NOTE:
If DTC P0345 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to
P0643.
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 10.5 V or more with ignition switch ON.
- GO TO 2.
2. PERFORM DTC CONFIRMATION PROCEDURE-I
1.Start engine and let it idle for at least 5 seconds.
If engine does not start, crank engine for at least 2 seconds.
2.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to .
NO- GO TO 3.
3. PERFORM DTC CONFIRMATION PROCEDURE-I
1.Maintain engine speed at more than 800 rpm for at least 5 seconds.
2.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to .
NO- INSPECTION END
Diagnosis Procedure
1. CHECK STARTING SYSTEM
Turn ignition switch to START position.
Does the engine turn over? Does the starter motor operate?
YES- GO TO 2.
NO- Check starting system. Initial Inspection and Diagnostic Overview.
2. CHECK CAMSHAFT POSITION SENSOR POWER SUPPLY CIRCUIT-I
1.Disconnect camshaft position (CMP) sensor harness connector.
2.Turn ignition switch ON.
3.Check the voltage between CMP sensor harness connector and ground.
Is the inspection result normal?
YES- GO TO 8.
NO-1- P0340: GO TO 3.
NO-2- P0345: Repair open circuit, short to ground or short to power in harness or connectors.
3. CHECK CMP SENSOR POWER SUPPLY CIRCUIT-II
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between CMP sensor harness connector and ECM harness connector.
Is the inspection result normal?
YES- GO TO 4.
NO- Repair open circuit.
4. CHECK SENSOR POWER SUPPLY CIRCUIT
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES- GO TO 5.
NO- Repair short to ground or short to power in harness or connectors.
5. CHECK COMPONENTS
Check the following.
- CKP sensor (P0335.)
- Camshaft position sensor (bank 1) (.)
- Battery current sensor (P1550.)
- EVAP control system pressure sensor (P0451.)
- Refrigerant pressure sensor (Refrigerant Pressure Sensor.)
Is the inspection result normal?
YES- GO TO 6.
NO- Replace malfunctioning component.
6. CHECK APP SENSOR
P2122.
Is the inspection result normal?
YES- GO TO 12.
NO- GO TO 7.
7. REPLACE ACCELERATOR PEDAL ASSEMBLY
Replace accelerator pedal assembly. Refer to following.
- Models without Distance Control Assist system: {LINK_TO_MANY:0000000006889129}{LINK_TO_MANY:0000000006889130}{LINK_TO_MANY:0000000006889131}, "MODELS WITHOUT DISTANCE CONTROL
ASSIST SYSTEM : Removal and Installation"
- Models with Distance Control Assist system: With Distance Control Assist System
- INSPECTION END
8. CHECK CMP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between CMP sensor harness connector and ECM harness connector.
4.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 9.
NO- Repair open circuit, short to ground or short to power in harness or connectors.
9. CHECK CMP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.Check the continuity between CMP sensor harness connector and ECM harness connector.
2.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 10.
NO- Repair open circuit, short to ground or short to power in harness or connectors.
10. CHECK CAMSHAFT POSITION SENSOR
.
Is the inspection result normal?
YES- GO TO 11.
NO- Replace malfunctioning camshaft position sensor.
11. CHECK CAMSHAFT SPROCKET (SIGNAL PLATE)
Check the following.
- Accumulation of debris to the signal plate of camshaft sprocket (INT)
- Chipping signal plate of camshaft sprocket (INT)
Is the inspection result normal?
YES- GO TO 12.
NO- Remove debris and clean the signal plate of camshaft sprocket (INT).
12. CHECK INTERMITTENT INCIDENT
Intermittent Incident.
- INSPECTION END
Component Inspection (Camshaft Position Sensor)
1. CHECK CAMSHAFT POSITION SENSOR-I
1.Turn ignition switch OFF.
2.Loosen the fixing bolt of the sensor.
3.Disconnect camshaft position sensor harness connector.
4.Remove the sensor. Exploded View.
5.Visually check the sensor for chipping.
Is the inspection result normal?
YES- GO TO 2.
NO- Replace malfunctioning camshaft position sensor.
2. CHECK CAMSHAFT POSITION SENSOR-II
Check resistance camshaft position sensor terminals as per the following.
Is the inspection result normal?
YES- INSPECTION END
NO- Replace malfunctioning camshaft position sensor.