Front Seat

FRONT SEAT

Disassembly and Assembly

SEATBACK

Disassembly
1.Remove the seat cushion outer finisher.

- Remove the seat slide and lifter switch knob (1) and seat reclining switch knob (2). Using a remover tool (A).

- Remove the metal clips, clips and pawls, and then pull out seat cushion outer finisher.

- Disconnect the seat control switch and side support switch harness connectors.
- Remove the reclining device outer cover (front, rear).

2.Remove the seat cushion inner finisher.
- Remove the reclining device inner covers (front, rear) by releasing the metal clip and pull it up together with the cover.
- Remove the relining device inner covers (front, rear) from the seat cushion inner finisher by releasing the pawls.

3.Remove the back board.

- Remove the metal clips and clips, and then pull out seatback board (1).
- Pull down the seatback board to release the upper pawls.

4.Remove the lumbar support lever knob.

Pull snap ring (1) upward, and remove lumbar support lever knob (2) from seatback frame with hook and pick tool.
5.Remove the seatback pad and trim.

- Remove the seatback retainer (1) on the back side of the seatback.

- Remove the headrest holder.

CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
- Remove the side air bag module.

- Remove the side support hose joint (1) located under the seat cushion. (Side support model only.)
- Disconnect the seatback heater unit harness connector.

- Disconnect the reclining motor harness connector (1) and remove the harness clamp.
- Disconnect the side support unit harness connector (2) and remove the harness clamp. (Side support model only.)
- Remove the seatback pad and seatback trim from the seatback frame.
- Remove the hog rings, and separate the trim and pad.
6.Remove the seatback silencer.
7.Remove the bolts, and then remove lumbar support unit.
8.Remove the side support bag and unit. (Side support model only.)

- Remove the pawls, and then remove side support bag (1).
- Remove the side support unit.

9.Remove the seatback frame.

Remove the seatback frame mounting bolts (A).
Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with the pad side wire.

SEAT CUSHION

Disassembly

CAUTION:
- Never disassemble front passenger seat cushion assembly.
- Always replace as an assembly.
- For front passenger seat service parts, refer to the service part catalogue.
1.Remove the seat cushion outer finisher.

- Remove the seat slide and lifter switch knob (1) and seat reclining switch knob (2). Using a remover tool (A).

- Remove the metal clips, clips and pawls, and then pull out seat cushion outer finisher.

- Disconnect the seat control switch and side support switch harness connectors.
- Remove the reclining device outer cover (front, rear).
2.Remove the seat cushion inner finisher.

- Remove the reclining device inner covers (front, rear) by releasing the metal clip and pull it up together with the cover.
- Remove the relining device inner covers (front, rear) from the seat cushion inner finisher by releasing the pawls.

3.Remove the seat cushion front finisher.

Remove the metal clips, and then pull out seat cushion front finisher (1).

4.Remove the seatback board.

- Remove the metal clips and clips, and then pull out seatback board (1).
- Pull down the seatback board to release the upper pawls.

5.Remove the seatback assembly.

- Remove the side support hose joint (1) located under the seat cushion. (Side support model only.)

- Remove the seatback mounting bolts (A), and then remove the seatback assembly.
6.Remove the thigh extension. (Thigh extension model only.)

- Remove the retainer.
- Remove the thigh extension pad.

- Remove the mounting screws (A).
- Remove the seat cushion trim wire (1) from the hooks (2).
- Remove the thigh extension frame by sliding it.
7.Remove the seat cushion pad and trim.

- Remove the clips (A). (Thigh extension model only.)
- Remove the retainer.
- Disconnect the seat cushion heater unit harness connector.
- Remove the hog rings, and separate the trim and pad.
8.Remove the side support bag. (Side support model only.)
- Remove the hose clamp.

- Remove the pawls, and then remove side support bag (1).

9.Remove the seat slide outer finisher.

- Remove the metal clips and pawls, and then pull out seat slide outer finisher (outside).
- Remove the metal clip, and then pull out seat slide outer finisher (inside).

10.Remove the seat slide inner finisher.

Remove the metal clip, and then pull out seat slide inner finisher.

Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord with the pad side wire.