Confirmation/Adjustment Mode

Confirmation/Adjustment Mode




1. Confirmation/Adjustment mode can be selected by starting the diagnosis function and selecting "Confirmation/Adjustment". The confirmation/adjustment of each item can be performed.




2. Select each screen switch of Confirmation/Adjustment screen to display the relevant diagnosis screen. Press the "BACK" switch to return to the initial screen of Confirmation/Adjustment.




DISPLAY DIAGNOSIS







VEHICLE SIGNALS
A comparison check can be made of each actual vehicle signal and the signals recognized by the system.

SPEAKER TEST




When selecting "Speaker Test", speaker diagnosis screen is displayed.
When pressing "START", test tone emits from the speaker.
At that time, when pressing "Start", test tone emits from next speaker. Then, when pressing the "End", test tone stops.

NOTE: The frequency of test tone emitted from each speaker is as follows.

Tweeter : 3 kHz
Front door speaker : 300 Hz
Rear door speaker : 1 kHz
Rear surround speaker : 1 kHz
Center speaker : 1 kHz
Woofer : 100 Hz
Seat speaker : 1 kHz

CLIMATE CONTROL
For details, refer to ATC-57, "Self-diagnosis Function". Without Scan Tool

NAVIGATION




Steering Angle Adjustment
The steering angle output value detected with the gyroscope can be adjusted.




Speed Calibration
Usually the automatic distance correction function adjusts the malfunction in distance caused by the tires wearing down or the tire pressure change. If prompt adjustment is necessary when the tire chains are installed etc., perform this procedure.

ERROR HISTORY
The diagnostic results of "Self-diagnosis" determine if any malfunction occurred between selecting "Self-diagnosis" and displaying "Self-diagnostic Results".

If an error occurred before the ignition switch was turned ON and does not occur again until "Self-diagnosis" is completed, the trouble diagnosis result will be judged normal. Therefore, errors in the past which cannot be found by "Self-diagnosis", must be found by checking the "Error record".
The error history shows the error occurrence frequency in past. The frequency of occurrence is displayed by 2 types: the count down type and the count up type. Select either type according to the error item.

In "Error History" of models with NAVI, time and place that the selected error last occurred are displayed. Be careful about the following.
- If there is a malfunction with the GPS antenna circuit board in the NAVI control unit, the correct date of occurrence may not be able to be displayed.
- Place of the error occurrence is represented by the position of the current location mark at the time an error occurred. If current location mark has deviated from the correct position, then the place of the error occurrence cannot be located correctly.

Transition Screen




Without NAVI




With NAVI

Count Down Type
- When the error is detected, set the counter to 40. If the system is normal when turning the ignition switch ON, the counter decreases by 1.
- The lower limit of the counter is 1. It can be reset to 0 by "Delete log" switch or CONSULT-II.




Count Up Type
- When the ignition switch is turned ON if the error is detected, the counter increases 1. Even if it is normal when the ignition switch is turned ON the next time, the counter does not decrease.
- The upper limit of the counter is 50. 51 or more is displayed as 50. It can be reset to 0 by "Delete log" switch or CONSULT-II.













Error Item
Some error items may be displayed simultaneously according to the cause. If some error items are displayed simultaneously, the detection of the cause can be performed by the combination of display items

VEHICLE CAN DIAGNOSIS




- CAN communication status and error counter is displayed.
- Error counter displays 0 if any malfunction is not detected in the past. If the malfunction is detected, it displays 40. When turning the ignition switch ON, if it is normal, it displays 39. The lower limit of the counter is 1.




- If it is reset, the error counter is deleted.

AV COMM DIAGNOSIS




- Displays the communication condition between AV (NAVI) control unit (master unit) and each unit and between audio unit (sub-master unit) and each unit.
- Error counter displays 0 if any malfunction is not detected in the past. If the malfunction is detected, it displays 40. When turning the ignition switch ON, if it is normal, it displays 39. The lower limit of the counter is 1.







- If it is reset, the error counter is deleted.

HANDSFREE PHONE




Handsfree Volume Adjustment
The received volume adjustment of hands-free phone can be adjusted to Low, Medium, and High settings.

Voice Microphone Test
When this function is turned ON, the voice that is input to microphone is output to front speaker via TEL voice signal line. The microphone and TEL voice signal line can be checked.

Delete Handsfree Memory
Erase the memory related to the hands-free phone.

REAR DISPLAY




- Tilt angle (90 to 135 degrees, 105 to 135 degrees) of rear seat display can be set.
- The automatic retraction of rear seat display can be set.

CAMERA CONT.
There are 2 functions: "Connection Confirmation", "Adjust offset of rear view camera".







Connection Confirmation
The input signals of steering angle sensor signal, reverse signal, and vehicle speed signal can be checked.




Adjust Offset of Rear View Camera
If the adjustment of rear view monitor guiding line display position is necessary when rear view camera is removed, use this mode to adjust it.

BLUETOOTH




Confirm/Change Passkey
- The passkey of Bluetooth can be confirmed and changed.
- The passkey can be changed by four digits within 0 to 9.




Confirm/Change Device Name
- The device name of Bluetooth can be confirmed and changed.
- The device name can be changed by sixteen digits within A to Z (small characters can be used) and - (hyphen).




DELETE UNIT CONNECTION LOG
Erase the connection history of unit and error history that is recorded in AV (NAVI) control unit (clear the connection history of the removed unit).

Rear View Monitor Guiding Line Adjustment




1. Draw lines on rearward area of the vehicle passing through the following points: 20 cm (7.87 in) from both sides of the vehicle, and 0.5 m (1.64 ft), 1.0 m (3.28 ft) from the rear end of the bumper.
2. Set into "Adjust offset of rear view camera" mode of Confirmation/Adjustment mode.




3. Rotate the center dial, and then select the guiding line pattern so that its angle is aligned with the correction line of the rear of the vehicle.

Selected pattern : 7

4. Make fine adjustment to the correction line of the rear of the vehicle with up/down/left/right switches so that its position is aligned with the guiding line. Press "OK" switch and record the adjusted guiding line position to the camera control unit.

Up/Down adjustment range : -20 - 20
Left/Right adjustment range : -20 - 20

CAUTION: Never operate other function such as pressing BACK while writing index data.
If Confirmation/Adjustment mode does not function in the above procedure, perform one of the following service to adjust the index again.
- Remove battery for five min. Then reconnect battery.
- Remove camera control unit connector for five min. Then reconnect camera control unit connector.