Vehicle Does Not Creep Backward In R Position

Vehicle Does Not Creep Backward In R Position
SYMPTOM:
The vehicle does not creep in the R position. Or an extreme lack of acceleration is observed.

DIAGNOSTIC PROCEDURE
1. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to SELF-DIAGNOSTIC RESULT MODE, With Manufacturer's Scan Tool and Without Scan Tool
Is any malfunction detected by self-diagnostic results?
YES >> Check the malfunctioning system. Refer to SELF-DIAGNOSTIC RESULT MODE, Judgement Self-Diagnosis Code.
NO >> GO TO 2.

2. CHECK CONTROL LINKAGE
Check the control linkage.
^ Refer to Checking of A/T Position.
OK or NG
OK >> GO TO 3.
NG >> Adjust control linkage. Refer to Adjustment of A/T Position.

3. CHECK A/T FLUID LEVEL





Check A/T fluid level. Refer to Checking A/T Fluid.
OK or NG
OK >> GO TO 4.
NG >> Refill ATF.

4. CHECK STALL TEST





Check stall revolution with selector lever in M and R positions.
Refer to STALL TEST.
OK or NG
OK >> GO TO 0.
OK in M position, NG in R position >> GO TO 5.
NG in both M and R positions >> GO TO 8.

5. DETECT MALFUNCTIONING ITEM
1. Disassemble A/T. Refer to DISASSEMBLY.
2. Check the following. Reverse brake. Refer to DISASSEMBLY.
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.

6. CHECK LINE PRESSURE





Check the line pressure with the engine idling. Refer to LINE PRESSURE TEST.
OK or NG
OK >> GO TO 9.
NG 1 >> Line pressure high. GO TO 7.
NG 2 >> Line pressure low. GO TO 8.

7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to Control Valve with TCM and A/T Fluid Temperature Sensor 2.
2. Disassemble A/T. Refer to DISASSEMBLY.
3. Check the following.
^ Oil pump assembly. Refer to Oil Pump.
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.

8. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to Control Valve with TCM and A/T Fluid Temperature Sensor 2.
2. Disassemble A/T. Refer to DISASSEMBLY.
3. Check the following.
^ Oil pump assembly. Refer to Oil Pump.
^ Power train system. Refer to DISASSEMBLY.
^ Transmission case. Refer to DISASSEMBLY.
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.

9. CHECK A/T FLUID CONDITION





1. Remove oil pan. Refer to Control Valve with TCM and A/T Fluid Temperature Sensor 2.
2. Check A/T fluid condition. Refer to Fluid Condition Check.
OK or NG
OK >> GO TO 10.
NG >> GO TO 13.

10. DETECT MALFUNCTIONING ITEM
^ Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to Symptom Chart (Symptom No.43).
OK or NG
OK >> GO TO 11.
NG >> Repair or replace damaged parts.

11. CHECK SYMPTOM
Check again. Refer to Check at Idle.
OK or NG
OK >> INSPECTION END
NG >> GO TO 12.

12. CHECK TCM
1. Check TCM input/output signals. Refer to TCM Input/Output Signal Reference Values.
2. If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> INSPECTION END
NG >> Repair or replace damaged parts.

13. DETECT MALFUNCTIONING ITEM
^ Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to Symptom Chart (Symptom No.43).
OK or NG
OK >> GO TO 11.
NG >> Repair or replace damaged parts.